Design of highly selective bandpass filters for communication between two satellites at K band frequency

Patel, Amit; Vala, Alpesh; Goswami, Riddhi; Mahant, Keyur

doi:10.1109/wamicon.2015.7120404

Cited by 7 publications

(5 citation statements)

References 12 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To begin with, it has been observed that HMSIW structure exhibits the high-pass response, presented in Figure 2(b). Band-pass response in the SIW structure can be achieved by utilizing several techniques such as inductive post based filter, defected ground structure, split-ring resonators, and stepped impedances [11][12][13][14][15][16][17]. However, a wide-band band-pass filter with SSPPs outstrips the other approaches because of ease of frequency tuning and implementation in HMSIW structure.…”

Section: Design Of Hmsiw and Sspps Based Wide Band Band-pass Filtermentioning

confidence: 99%

Spoof Surface Plasmon Polaritons and Half-Mode Substrate Integrated Waveguide Based Compact Band-Pass Filter for Radar Application

Mahant¹,

Mewada²,

Patel³

et al. 2021

PIER M

Self Cite

View full text Add to dashboard Cite

A band-pass filter using spoof surface plasmon polaritons (SSPPs) and half-mode substrate integrated waveguide (HMSIW) for Ka-band RADAR application is proposed. In order to achieve the band-pass response, an HMSIW structure with high pass response and SSPPs with band-stop response are combined. Moreover, to investigate effects of geometric dimensions on the frequency characteristics of the proposed band-pass filter are examined by parametric analysis. It has been observed that lower cutoff and upper frequencies can be individually controlled just by changing the structural parameters. High Frequency Structure Simulator (HFSS) software was utilized to simulate the proposed structure. HFSS is the simulation tool for complex 3-D geometries and uses the finite element method (FEM). To validate the functionality, the proposed band-pass filter is fabricated on the dielectric material RT duroid 5880 with the dielectric constant ε r = 2.2, height h = 0.508 mm, and dissipation factor tan δ = 4× 10 −4. The measured result shows return loss better than −10 dB and insertion loss less than 1.25 dB with the 3 dB fractional bandwidth (FBW) of 44.02% at the center frequency of 7.95 GHz.

show abstract

Section: Design Of Hmsiw and Sspps Based Wide Band Band-pass Filtermentioning

confidence: 99%

Spoof Surface Plasmon Polaritons and Half-Mode Substrate Integrated Waveguide Based Compact Band-Pass Filter for Radar Application

Mahant¹,

Mewada²,

Patel³

et al. 2021

PIER M

Self Cite

View full text Add to dashboard Cite

show abstract

“…Microwave filters have been developed recently based on several methods and techniques, such as microstrip line [1], conventional waveguide technology [2], photonic band gap structure [1], metamaterial structure [3], and substrate integrated waveguide (SIW) technology [4].…”

Section: Introductionmentioning

confidence: 99%

Corrugated Siw Based Bandpass Filter for Microwave Interferometer and Ism Band Application

Vala¹,

Patel²,

Mahant³

et al. 2021

PIER C

Self Cite

View full text Add to dashboard Cite

A corrugated substrate integrated waveguide (CSIW) based bandpass filter is designed and developed for the microwave interferometer (7.0 GHz) and ISM band (5.7 GHz-5.9 GHz) application. CSIW structure provides a cost-effective solution counter to substrate integrated waveguide (SIW). Initially, the CSIW structure is designed from the design methodology of SIW. Vias are replaced with a quarter wavelength open stub. A metallic inductive post is used for the realization of the bandpass filter from the CSIW structure. Computer simulation technology (CST) software is used for design and simulation of the proposed model. Two structures are implemented for the microwave interferometer and ISM band frequency application. The first structure resonates at the center frequency of 7.023 GHz with the fractional bandwidth of 5.26%. It provides an insertion loss value of less than 1.5 dB and a return loss better than 14 dB. Similarly, the second structure provides passband frequency, from 5.6 GHz to 6.0 GHz, with the insertion loss value less than 1.5 dB and return loss better than 18 dB at the center frequency. It can be used for the ISM band frequency application. The frequency tuning approach is also shown to change the resonance frequency for different applications. For the proof of concept, the proposed filter is fabricated and tested. The measured results are quite similar to the simulation results.

show abstract

“…SIW technology is an emerging technology, in which structure contains dielectric material with top and bottom metallic surface and two linear arrays of metal vias connecting top and bottom metallic surface embedded with dielectric material . This technology provides the advantages of microstrip circuits like small size, low‐cost and easy fabrication and it also provides the demanding properties of the bulky waveguide like high power handling capacity and low insertion losses with less weight . In 2004, Falcone, Francisco, et al introduced the metamaterial resonators and it was proven that SRR exhibits negative permittivity, which attracts many researchers in the field of RF and microwave.…”

Section: Introductionmentioning

confidence: 99%

“…6,7 This technology provides the advantages of microstrip circuits like small size, low-cost and easy fabrication and it also provides the demanding properties of the bulky waveguide like high power handling capacity and low insertion losses with less weight. 6,7,19 In 2004, Falcone, Francisco, et al 5 introduced the metamaterial resonators and it was proven that SRR exhibits negative permittivity, which attracts many researchers in the field of RF and microwave. The detail characteristics of SRRs and CSRRs have been investigated in.…”

Section: Introductionmentioning

confidence: 99%

Substrate Integrated Waveguide based dual‐band bandpass filter using split ring resonator and defected ground structure for SFCW Radar applications

Mahant

Mewada²

2018

Int J RF Microw Comput Aided Eng

Self Cite

View full text Add to dashboard Cite

In this paper, we present a novel dual‐band highly selective bandpass filter using Substrate Integrated Waveguide (SIW) technology. Designed bandpass filter is a combination of SIW structure with high‐pass characteristic, single rectangular split ring resonators (SRRs) as parallel LC resonator & dumbbell‐ shaped defected ground structure (DGS) with band rejection characteristic. Here, designed filter has pass band with high rejection values of −15.24 dB and − 18.43 dB and the insertion loss of 0.250 dB and 0.361 dB at 6 GHz and 8.55 GHz respectively. Designed SIW based dual‐band bandpass filter has 3‐dB fractional bandwidth (FBW) of 2.85% and 2.22% at 6GHz and 8.55 GHz respectively. The physical dimension of proposed structure is of 42 mm x 21 mm (1.77 λg x 0.88 λg). All the simulations and optimizations of the proposed structure are carried out in the Ansoft HFSS (high frequency structure simulator) software based on the finite element method. In order to verify the functionality of the proposed filter, structure is fabricated and tested.

show abstract

Design of highly selective bandpass filters for communication between two satellites at K band frequency

Cited by 7 publications

References 12 publications

Spoof Surface Plasmon Polaritons and Half-Mode Substrate Integrated Waveguide Based Compact Band-Pass Filter for Radar Application

Spoof Surface Plasmon Polaritons and Half-Mode Substrate Integrated Waveguide Based Compact Band-Pass Filter for Radar Application

Corrugated Siw Based Bandpass Filter for Microwave Interferometer and Ism Band Application

Substrate Integrated Waveguide based dual‐band bandpass filter using split ring resonator and defected ground structure for SFCW Radar applications

Contact Info

Product

Resources

About