Designing a voltage control system of the magnetoelectric generator with magnetic flux shunting for electric power systems

Ostroverkhov, Мykola; Chumack, Vadim; Tymoshchuk, Oksana; Kovalenko, Mykhailo; Ihnatiuk, Yevhen

doi:10.15587/1729-4061.2022.265861

Cited by 2 publications

(2 citation statements)

References 11 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…When affected by fast-moving processes, it is important to take into account such indicators that are not valid at the operating frequency, namely, the inductance of the winding link, which in this case is a section, capacitance per case, impedance per case [13].…”

Section: High-frequency Replacement Circuit For Calculations and Anal...mentioning

confidence: 99%

Design of a multilink system for calculating high-frequency processes in electric machines with mesh windings

Chumack

Kovalenko

Tymoshchuk³

et al. 2023

EEJET

View full text Add to dashboard Cite

This study considers the design of a multi-link high-frequency circuit for calculating defective and defect-free insulation of mesh windings in order to increase the operational reliability of general-purpose electric machines. The object of research is mesh windings of electric machines. The problem to be solved: increasing the operational reliability of electric machines with general-purpose mesh windings by analyzing and modeling defects. The research results make it possible to model defects for the analysis of the state of insulation of electric machines with mesh windings. Special attention in the research was paid to induction motors with a worn-out resource, in particular, 4A80A4 UZ engine. The analysis includes phase-to-body capacitance, winding inductance, eddy current impedance, and winding impedance. Under the WN mode, a decrease in the impedance of the winding section from 3 % to the short-circuit mode was simulated; accordingly, the resonance frequencies for each case of 3 % were determined – 73990 Hz, short-circuit – 74450 Hz, as well as the corresponding input impedances 8938.7 and 8082.5. The corresponding voltage resonances and current resonances were also determined. Appropriate results were also given for the WG scheme. The results reported here relate to the design of the scheme and the research on the defects of the mesh winding. This contributes to the analysis of the state of insulation of mesh windings. The numerical data (resonant frequencies and input impedances) allow a better understanding of the behavior of windings in different states and degrees of defects. Given the research findings, it is possible to better identify and analyze potential defects in mesh windings, which in turn contributes to increasing the reliability of electric machines. The results of this study could be used in the field of diagnosis, service, and maintenance of electric machines with mesh windings

show abstract

Section: High-frequency Replacement Circuit For Calculations and Anal...mentioning

confidence: 99%

Design of a multilink system for calculating high-frequency processes in electric machines with mesh windings

Chumack

Kovalenko

Tymoshchuk³

et al. 2023

EEJET

View full text Add to dashboard Cite

show abstract

“…Well-known Maxwell's equations [14,15] are used to study the dynamic processes in individual sheets of a charged magnetic conductor.…”

Section: Development Of a Mathematical Model Of Individual Sheets Of ...mentioning

confidence: 99%

Research of high-frequency remagnetization model in laminated magnetic cores of electromechanical and electromagnetic energy converters

Kovalenko,

Chumack,

Tymoshchuk

et al. 2023

EEJET

View full text Add to dashboard Cite

The object of research in the work is charged magnetic conductors of electric machines and transformers. Laminated magnetic wire together with windings are important active parts of electric machines that participate in electromechanical energy conversion. The reliability of the entire machine is mainly determined by the actual condition of the inter-sheet insulation. Violation of the insulation causes parasitic eddy current circuits, which increases the specific losses, and also significantly affects the additional heating of the magnet wire and winding. The normative method for determining the quality of the charged core is the assessment of specific losses at a frequency of 50 Hz and an induction of 1 T, which should not exceed 2.5–4 W/kg. To determine local damage to the core, methods of local heating and fixation of overheating sites are used, which should not exceed 45 °C compared to the main part of the magnetic core. In the work, a two-dimensional field mathematical model of a charged magnetic circuit is developed. This makes it possible to carry out electromagnetic calculations in a near-real magnetic conductor, taking into account the variability of magnetic permeability, hysteresis, and the interaction of currents in adjacent plates of the magnetic conductor with each other, the so-called "proximity effect". On the basis of the developed models, graphs of current distribution and distribution of magnetic induction in one, two and three sheets were obtained. The resulting graphs show how the effect of current displacement increases with increasing frequency, where at a frequency of 100 kHz the magnetic induction density in the middle of the sheet goes to zero. The results of the research confirm the correctness of the model development in comparison with the classical calculation models also given, which allows them to be used for further research of high-frequency processes in charged magnetic circuits of electric machines

show abstract

Designing a voltage control system of the magnetoelectric generator with magnetic flux shunting for electric power systems

Cited by 2 publications

References 11 publications

Design of a multilink system for calculating high-frequency processes in electric machines with mesh windings

Design of a multilink system for calculating high-frequency processes in electric machines with mesh windings

Research of high-frequency remagnetization model in laminated magnetic cores of electromechanical and electromagnetic energy converters

Contact Info

Product

Resources

About