Development and Automation of the Device for Determination of Thermophysical Properties of Polymers and Composites

Bakanin, D. V.; Bychkovsky, Vladimir; Филиппенко, Николай Григорьевич; Butorin, D. V.; Kuraitis, A. S.

doi:10.1007/978-3-030-19756-8_69

Cited by 6 publications

(1 citation statement)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The authors did not find the optimal conditions for their use. The impact of abrasive particles on the working surfaces of mated parts creates the conditions for increasing a temperature mode and the conditions for hard-particle grinding [13]. However, the authors did not establish any effect of the wear particle size on the condition of polymeric materials.…”

Section: Literature Review and Problem Statementmentioning

confidence: 96%

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Аулин

Derkach

Makarenko

et al. 2019

EEJET

View full text Add to dashboard Cite

Section: Literature Review and Problem Statementmentioning

confidence: 96%

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Аулин

Derkach

Makarenko

et al. 2019

EEJET

View full text Add to dashboard Cite

Contact method of volume control of temperature of a polymer sample at high-frequency heating

Bychkovsky

Bakanin

Филиппенко

et al. 2020

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

This paper presents the results of research of the contact method of volumetric temperature control of a polymer sample. The scheme of thermocouples (TC) location in a polymer sample, finite-element model and general mathematical model for calculating the influence of the quantity of thermocouples on heating samples at high-frequency processing are constructed. Comparative analysis of the obtained results was conducted.

show abstract

Automated control of the production process of antifriction polymer materials

Filippenko

Bychkovsky

Bakanin

et al. 2021

J. Phys.: Conf. Ser.

View full text Add to dashboard Cite

This paper presents a technique of controlling the process of oil filling of polymer and composite materials, which allows automated determination of volumetric heating of a polymer or composite sample for the purpose of drying. The differentiation of the obtained results, presented in graphical form, made it possible to quickly analyze the dynamics of temperature changes in the thickness of the material, the change of which determines the rates and time of impregnation to a certain depth of the body of the polymer or composite sample in figure 1. According to the developed methodology, studies of the impregnation of the oil filler of a mixture of M8-B motor oil and hexane were carried out. For each experiment, time dependences of the impregnation rate were obtained. Based on the work carried out, the optimal proportion of a mixture of hexane and engine oil and the most favourable temperature conditions were determined. At the end of the research, the assumption about the possibility of using this technique for the purpose of its industrial use in the technology of oil filling of antifriction products made of polymer and composite materials was confirmed.

show abstract

Development and Automation of the Device for Determination of Thermophysical Properties of Polymers and Composites

Cited by 6 publications

References 2 publications

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Contact method of volume control of temperature of a polymer sample at high-frequency heating

Automated control of the production process of antifriction polymer materials

Contact Info

Product

Resources

About

Development and Automation of the Device for Determination of Thermophysical Properties of Polymers and Composites

Cited by 6 publications

References 2 publications

Analysis of tribological efficiency of movable junctions "polymeric­composite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymeric­composite materials ‒ steel"

Contact method of volume control of temperature of a polymer sample at high-frequency heating

Automated control of the production process of antifriction polymer materials

Contact Info

Product

Resources

About

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"

Analysis of tribological efficiency of movable junctions "polymericcomposite materials ‒ steel"