Discrete framelet transform based OFDM system using N-FRAT mapping over Rayleigh fading channel

Hadi, Suha Q.; Ehkan, Phaklen; Anuar, M. S.; Dawood, Sameer A.

doi:10.1007/s11276-016-1367-z

Cited by 3 publications

(5 citation statements)

References 17 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…In the FRAT mapping procedure, a two dimensional FFT (2D-FFT) will be applied on this A and then the resulted matrix will be reordering by applying the optimal ordering algorithm [8] to produce the optimal matrix (F opt ). After that one dimensional IFFT (1D-IFFT) will be applied on each columns of the F opt to obtain FRAT matrix .…”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“… In order to increase the bit per Hertz of the mapping, the complex matrix  will be constructed from the real matrix ,  according to the equation (1) [8].…”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“…The N f -point of inverse FT (IFT) is then applied to the signal to achieve orthogonality between subcarriers. The procedure of IFT is based on the matrix multiplication between the reconstruction matrix (W 2 ) given in equation (2) and the input signal [8]. The h 0 , h 1 , and h 2 are the low and two high-pass filter coefficients.…”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“…At the receiver, the inverse operations for each block in the transmitter side must be performed to produce the correct data stream [8]. …”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“…This article aims to present an efficient design and implementation of the FRAT-FT-OFDM model [8] on FPGA platform using a higher abstraction level tool called Xilinx System Generator (XSG) which is a part of System Editions of Vivado ® Design Suite. The Vivado Design Suite (v2015.2) will be used in this work.…”

mentioning

confidence: 99%

See 4 more Smart Citations

Implementation of Radon-Framelet Based OFDM on FPGA Platform

Hadi¹

2017

IJET

View full text Add to dashboard Cite

Abstract-This article proposes an efficient design and implementation of Framelet-Based Orthogonal Frequency Division Multiplexing (OFDM) with Finite Radon Transform (FRAT), named as (FRAT-FT-OFDM), on Field ProgrammableGate Array (FPGA) platform. Modern FPGA design tool called Xilinx System Generator (XSG) is used to implement the transceiver of FRAT-FT-OFDM system. The FPGA implementation is carried out on a Zynq (XC7Z020-1CLG484) evaluation board with Joint Test Action Group (JTAG) hardware co-simulation. Performance of the implemented architecture has been validated through hardware co-simulation in term of utilized area and consumed power. The results showed that the system was implemented efficiently with few resources and consumed power, and could support realtime operations.Keyword -OFDM, Framelet Transform, Radon Transform, FPGA, Xilinx System Generator I. INTRODUCTION Orthogonal Frequency Division Multiplexing (OFDM) is a special case of multicarrier transmission technique for achieving high data rate transmission over multipath fading channel. It has been widely applied in many wireless and mobile networks especially for the communication standards [1]. In conventional OFDM system, Inverse Fast Fourier Transform (IFFT) is used at transmitter side and Fast Fourier Transform (FFT) is used at receiver side to generate orthogonal subcarriers [2]. The derivation of the system model also shows that by introducing a Cyclic Prefix (CP), the orthogonality can be maintained over a dispersive channel and the Inter-Symbol Interference (ISI) can be avoided but this come at the cost of decreasing the transmission efficiency and increasing complexity of the system [3].OFDM based on wavelet transforms were also proposed by a number of researchers [4][5][6][7]. The idea of using wavelet transform instead of Fourier transform, because of its high spectral containment properties compared with Fourier transform. Among these, Framelet transform-based OFDM (FT-OFDM) [6] was shown to have better Bit Error Rate (BER) performance than Discrete Wavelet Transform (DWT)-based OFDM and FFTbased OFDM. However, FT-OFDM is unsuitable for outdoor wireless applications, where data must be transmitted at high rates with Doppler spread robustness. Therefore, Hadi et al. [8] improved the performance of FT-OFDM system by using Finite Radon Transform (FRAT) as a mapping technique and combined it with FT to produce a new model called as FRAT-FT-OFDM system. In this system, Radon transform was used as a mapping technique instead of conventional mapping techniques such as Quadrature Amplitude Mapping (QAM), and the FT was used to realize the multicarrier modulation instead of FFT or DWT.For the time being, hardware realization of OFDM system using Field Programmable Gate Array (FPGA) is an important area of research due to the speed of implementation, low development costs and less time to market with the ability to reduce the complexity and power consumption without sacrificing in the performance of the system [9]. FPGA is truly parallel in...

show abstract

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“… In order to increase the bit per Hertz of the mapping, the complex matrix  will be constructed from the real matrix ,  according to the equation (1) [8].…”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

“…At the receiver, the inverse operations for each block in the transmitter side must be performed to produce the correct data stream [8]. …”

Section: Fig 1 Basic Blocks Of Frat-ft-ofdm Transceivermentioning

confidence: 99%

mentioning

confidence: 99%

See 3 more Smart Citations