Effect of coaxial laser cladding parameters on bead formation

Noskov, A.I.; Gil'mutdinov, A. Kh.; Yanbaev, R. M.

doi:10.1007/s12613-017-1436-z

Cited by 9 publications

(7 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…[25]. Additionally, the presence of new peaks at b+ were found for the structure as well [25,26]. While alloy 5-13Ni alloy has a pearlite structure with austenite grains, a needle-shaped martensitic structure has locally segregated next to austenite grains in alloy 6-15Ni alloy.…”

Section: Resultsmentioning

confidence: 85%

“…While alloy 1-0Ni, alloy 2-NbV and alloy 3-5Ni alloys containing 5% Ni respectively give similar peaks, the peaks at 2-theta 65 • and 82. [25]. Additionally, the presence of new peaks at b+ were found for the structure as well [25,26].…”

Section: Resultsmentioning

confidence: 87%

“…For the alloys containing 20% and above of Ni, new peaks are formed at 43.60° and the peak at 44° of the alloy containing 40% Ni is completely damped. In high Ni contents, the peaks at 43° and 44° to the left indicate that the structure has transformed into FCC and the Fe3Ni compound may have formed [25]. Additionally, the presence of new peaks at b+ were found for the structure as well [25,26].…”

Section: Resultsmentioning

confidence: 97%

“…In high Ni contents, the peaks at 43° and 44° to the left indicate that the structure has transformed into FCC and the Fe3Ni compound may have formed [25]. Additionally, the presence of new peaks at b+ were found for the structure as well [25,26]. Table 2 list the hardness, yield strength (YS), ultimate tensile strength (UTS) and ductility in terms of the elongation at fracture of the alloys with and without Ni addition.…”

Section: Resultsmentioning

confidence: 99%

See 3 more Smart Citations

The Effect of Nickel on the Microstructure, Mechanical Properties and Corrosion Properties of Niobium–Vanadium Microalloyed Powder Metallurgy Steels

et al. 2020

View full text Add to dashboard Cite

In this study, the effects of adding Ni in different ratios to Fe-matrix material containing C-Nb-V produced by powder metallurgy on microstructure, tensile strength, hardness and corrosion behaviors were investigated. Fe-C and Fe-C-Nb-V powders containing 5%, 10%, 13%, 15%, 20%, 30% and 40% nickel were pressed at 700 MPa and then sintered in an Ar atmosphere at 1400 °C. Microstructures of the samples were characterized with optical microscope, scanning electron microscope (SEM) and XRD. Corrosion behaviors were investigated by obtaining Tafel curves in an aqueous solution containing 3.5% NaCl. Mechanical properties were determined by hardness and tensile testing. While Fe-C alloy and Fe-C-Nb-V microalloyed steel without Ni typically have a ferrite-pearlite microstructure, the austenite phase has been observed in the microstructures of the alloys with 10% nickel and further. Yield and tensile strength increased with nickel content and reached the highest strength values with 13% Ni content. The addition of more nickel led to decrease the strength. Analysis of Tafel curves showed that corrosion resistance of alloys increased with increasing nickel concentration.

show abstract

Section: Resultsmentioning

confidence: 85%

Section: Resultsmentioning

confidence: 87%

Section: Resultsmentioning

confidence: 97%

Section: Resultsmentioning

confidence: 99%

See 2 more Smart Citations

The Effect of Nickel on the Microstructure, Mechanical Properties and Corrosion Properties of Niobium–Vanadium Microalloyed Powder Metallurgy Steels

et al. 2020

View full text Add to dashboard Cite

show abstract

“…The dilution ratio was calculated based on the clad layer geometry [ 37 , 38 ]. It is defined as the ratio of the clad depth (D c ) in the substrate over the total clad height (T c ), according to the following equation: D R = D c /T c , where T c is the summation of the clad height and the clad depth.…”

Section: Resultsmentioning

confidence: 99%

Laser Powder Cladding of Ti-6Al-4V α/β Alloy

et al. 2017

View full text Add to dashboard Cite

Laser cladding process was performed on a commercial Ti-6Al-4V (α + β) titanium alloy by means of tungsten carbide-nickel based alloy powder blend. Nd:YAG laser with a 2.2-KW continuous wave was used with coaxial jet nozzle coupled with a standard powder feeding system. Four-track deposition of a blended powder consisting of 60 wt % tungsten carbide (WC) and 40 wt % NiCrBSi was successfully made on the alloy. The high content of the hard WC particles is intended to enhance the abrasion resistance of the titanium alloy. The goal was to create a uniform distribution of hard WC particles that is crack-free and nonporous to enhance the wear resistance of such alloy. This was achieved by changing the laser cladding parameters to reach the optimum conditions for favorable mechanical properties. The laser cladding samples were subjected to thorough microstructure examinations, microhardness and abrasion tests. Phase identification was obtained by X-ray diffraction (XRD). The obtained results revealed that the best clad layers were achieved at a specific heat input value of 59.5 J·mm−2. An increase by more than three folds in the microhardness values of the clad layers was achieved and the wear resistance was improved by values reaching 400 times.

show abstract

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

Yang

Liu

et al. 2019

Int J Miner Metall Mater

View full text Add to dashboard Cite

Effect of coaxial laser cladding parameters on bead formation

Cited by 9 publications

References 7 publications

The Effect of Nickel on the Microstructure, Mechanical Properties and Corrosion Properties of Niobium–Vanadium Microalloyed Powder Metallurgy Steels

The Effect of Nickel on the Microstructure, Mechanical Properties and Corrosion Properties of Niobium–Vanadium Microalloyed Powder Metallurgy Steels

Laser Powder Cladding of Ti-6Al-4V α/β Alloy

Enhanced mechanical properties and formability of 316L stainless steel materials 3D-printed using selective laser melting

Contact Info

Product

Resources

About