Effect of resin cement elastic modulus on the biaxial flexural strength and structural reliability of an ultra-thin lithium disilicate glass–ceramic material

Reis, Ana Flávia Nunes; Borges, Alexandre Luiz Souto; Paradella, Thaís Cachuté; Assis, Rita Adriana Souza da Silva de; Valandro, Luiz Felipe; Melo, Renata Marques de

doi:10.1007/s00784-022-04836-9

Cited by 2 publications

(1 citation statement)

References 33 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Currently, the studies conducted on this topic mainly evaluate biomaterials presented as luting cements, and therefore have a dual-curing mode. Their results generally confirm that the application and polymerization of a composite resin on a veneer increases its flexural strength [ 31 , 32 ].…”

Section: Discussionmentioning

confidence: 70%

Effects of Translucency and Thickness of Lithium Disilicate-Reinforced Glass-Ceramic Veneers on the Degree of Conversion of a Purely Light-Curing Bonding Resin: An In Vitro Study

et al. 2023

View full text Add to dashboard Cite

The objective of this study was to evaluate the variations in the degree of conversion (DC) of a light-curing composite resin when the thickness or the translucency of lithium disilicate-enriched glass-ceramic veneers are modified. IPS e. max® CAD blocks of the MT-A2, LT-A2 and MO1 types were cut to obtain four slices with thicknesses ranging from 0.6 mm to 1 mm. A strictly light-curing composite resin (G-aenial Universal Injectable) was injected in the empty part of a silicone mold so that the veneer could then be inserted under digital pressure to the stop. A 40 s light cure (1400 mW/cm2) was then performed. Resin samples were analyzed using Fourier transform infrared (FTIR) spectroscopy. When the degree of translucency of the ceramic was modified, a decrease in the resin conversion rate was noted, but with a non-significant global p-value (p = 0.062). Interestingly, the degree of conversion of the light-curing composite resin was also modified when the ceramic’s thickness increased, especially when it was over 1 mm (DC0.6 > DC0.7 > DC0.8 > DC1; p < 0.0001). This confirms that the degree of conversion of a bonding material is very dependent on the ceramic’s thickness. Contradictory data are, however, found in the literature, where there are reports of an absence of a difference between the DC obtained with thicknesses of ceramics of 0.7 and 2 mm.

show abstract

Section: Discussionmentioning

confidence: 70%

Effects of Translucency and Thickness of Lithium Disilicate-Reinforced Glass-Ceramic Veneers on the Degree of Conversion of a Purely Light-Curing Bonding Resin: An In Vitro Study

et al. 2023

View full text Add to dashboard Cite

show abstract

A comprehensive study on MDP effects: Microshear bond strength and fatigue resistance in 4YSZ ceramics

Rosa,

Souza,

Chiapinotto

et al. 2024

Braz. Dent. J.

View full text Add to dashboard Cite

The aim of this study is to assess the presence of MDP at various stages of the bonding procedure, enhance the adhesive and mechanical behavior of cemented zirconia ceramics. Fifty ceramic slices (15 × 15 × 2 mm) and 48 discs (Ø= 10 mm, 1 mm thickness) were prepared, sintered, air-abraded with aluminum oxide, and allocated considering: 1) microshear bond strength (µSBS) between ceramic slices and luting agent cylinders (height= 1 mm, Ø= 1.2 mm); 2) fatigue behavior, ceramic discs paired and bonded onto fiber-epoxy resin discs (Ø= 10 mm, 2.5 mm thickness), and then mechanically tested (cyclic loading, starting at 400N, with increments of 100N, until failure). Four experimental groups were defined: Universal Primer (MDP primer+non-MDP resin cement - RC), Universal Adhesive (MDP adhesive+non-MDP RC), Cement (no primer+MDP RC), and Primer+Cement (MDP primer + MDP RC). For both outcomes, half of the specimens were tested after 24 hours, and half after aging. Bond strength data was analyzed via two-way ANOVA and Tukey post-hoc tests, while fatigue data went through Kaplan-Meier and Mantel-Cox post hoc tests. Regarding µSBS, aging impaired adhesion only for the Primer+Cement group (p<0.001). Universal Primer and Universal Adhesive showed the highest bond strength (p<0.05). Despite that, fatigue data indicates no significant differences (p>0.05). In conclusion, systems with MDP-containing components associated with non-MDP resin cement demonstrated enhanced adhesive capability for zirconia restorations. Nevertheless, no differences in terms of mechanical reinforcement were observed.

show abstract

Effect of resin cement elastic modulus on the biaxial flexural strength and structural reliability of an ultra-thin lithium disilicate glass–ceramic material

Cited by 2 publications

References 33 publications

Effects of Translucency and Thickness of Lithium Disilicate-Reinforced Glass-Ceramic Veneers on the Degree of Conversion of a Purely Light-Curing Bonding Resin: An In Vitro Study

Effects of Translucency and Thickness of Lithium Disilicate-Reinforced Glass-Ceramic Veneers on the Degree of Conversion of a Purely Light-Curing Bonding Resin: An In Vitro Study

A comprehensive study on MDP effects: Microshear bond strength and fatigue resistance in 4YSZ ceramics

Contact Info

Product

Resources

About