Effect of temperature rise on the performance of induction motors

Khalifa, F. A.; Serry, Sobhy; Ismail, Mohamed M.; Elhady, Basem

doi:10.1109/icces.2009.5383074

Cited by 15 publications

(3 citation statements)

References 3 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Another standard focuses on optimum temperature controls, [24]. The exploration and improvement of the study of those standards found that efficiency is the first and most important parameter, because, performance and cost are functions of efficiency.…”

Section: Literature Reviewmentioning

confidence: 99%

Energy Efficiency Optimization of Three Phase Induction Motor Drives for Industrial Applications

Eseosa¹,

Christian²

2018

IJEAS

View full text Add to dashboard Cite

Section: Literature Reviewmentioning

confidence: 99%

Energy Efficiency Optimization of Three Phase Induction Motor Drives for Industrial Applications

Eseosa¹,

Christian²

2018

IJEAS

View full text Add to dashboard Cite

“…Whereas, in other standard, the performance of the motor was treated as the important parameter of the standard where the amount of active material, that is, lamination steel, copper or aluminium or magnet wire, and rotor aluminium was selected as the minimum levels required which is expected to increase the performance of the motor (Peter et al, 2007;Tessarolo et al, 2009). Another standard focused on the efficiency where the efficiency is maintained at optimum levels to manage and control the temperature requirements of the particular motor (Khalifa et al, 2009). The exploration and improvement of the study of those standards found that efficiency is the first and most important parameter since efficiency will create holistic environment which combines and balance the motor efficiency, cost and performance.…”

Section: Energy Efficiency Of Squirrel Cage Induction Motor (Scim) Stmentioning

confidence: 99%

Improving squirrel cage induction motor efficiency: Technical review

Razali

Abdalla²,

Ghoni³

2012

Int. J. Phys. Sci.

View full text Add to dashboard Cite

Studying and improving of Squirrel Cage Induction Motor (SCIM) efficiency is a continuous area of interest not only among the researchers but also the industry, manufacturer and government. However, until today there are still struggles to find the most holistic environment of the SCIM which achieve its efficiency at the most lowest cost and at the same time sustaining the performance of the motor. This paper will focus on the method on improving SCIM efficiency. The first discussion presented the main importance of efficient motors and its drive systems. These are partly conceptual, partly concerning circuit topology and current commutation technique. The second discussion ooptimization of SCIM efficiency using intelligent techniques which are of particular interest. The third discussion describes the energy efficiency of SCIM standards and most effect motor parameters on SCIM efficiency.

show abstract

“…Excessive temperature increases the rate of deterioration of the insulation of the motor windings, degradation of lubricant, and bearing failures [7]. Burning out of motor windings results from insulation failure, and every 10% increase in temperature reduces the insulation life by 50% [4].…”

Section: Introductionmentioning

confidence: 99%

Development of a Starter with Protective Systems for a Three-Phase Induction Motor

Orovwode

Matthew

Agbetuyi

et al. 2021

Journal of Engineering

View full text Add to dashboard Cite

Frequent burning of three-phase induction motors windings has been reported. The initial symptoms observed before the burning of the windings were an increase in operating current and a temperature rise. The induction motor protection and control system was designed, developed, and constructed to reduce the problem of burnt winding by early detection and disconnection of supply if the problem persists. It was found to be efficient, reliable, durable, and rugged. The system is a boost to Nigerian industrialists as it will reduce cases of burning of induction motors and the consequent downtime and cost. The system is cheap and easy to repair and maintain because the parts and components used in the design are available locally.

show abstract

Effect of temperature rise on the performance of induction motors

Cited by 15 publications

References 3 publications

Energy Efficiency Optimization of Three Phase Induction Motor Drives for Industrial Applications

Energy Efficiency Optimization of Three Phase Induction Motor Drives for Industrial Applications

Improving squirrel cage induction motor efficiency: Technical review

Development of a Starter with Protective Systems for a Three-Phase Induction Motor

Contact Info

Product

Resources

About