Effect of the Geometry of Thin-Walled Aluminium Alloy Elements on Their Deformations after Milling

Zawada-Michałowska, Magdalena; Kuczmaszewski, Józef; Pieśko, Paweł

doi:10.3390/ma15249049

Cited by 14 publications

(10 citation statements)

References 46 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…It is also important to observe the variable value of deformations on the crosssection of the sample. The authors of the paper [22] analyzed the deformation of thin-walled elements with vertical walls of aluminum alloy EN AW7075 T651 using conventional milling and highspeed machining for finishing. The result of their studies was the measurement of deformation carried out using a coordinate measuring machine.…”

Section: Introductionmentioning

confidence: 99%

“…High-quality companies use such systems that give the necessary information [29,30]. The term "information system" can be defined as a system of formalized procedures that enable the management of internal and external information, which is used for planning, management, and control purposes [19,[22][23][24][25][26][27][28][29][30][31][32][33][34][35].…”

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

et al. 2023

View full text Add to dashboard Cite

Thin-walled elements are widely used in the aerospace industry, where the aim is to reduce the process time and the weight of the structure while ensuring the sufficient quality of the finished product. Quality is determined by geometric structure parameters and dimensional and shape accuracy. The main problem encountered during the milling of thin-walled elements is the deformation of the product. Despite the various methods available for measuring deformation, more are still being developed. This paper presents selected surface topography parameters and deformation of vertical thin-walled elements during an experiment under controlled cutting conditions for samples from titanium alloy Ti6Al4V. Constant parameters of feed (f), cutting speed (Vc,) and tool diameter (D) were used. Samples were milled using a tool for general-purpose and a tool for high-performance machining, as well as two different machining approaches: with greater involvement of face milling, and cylindrical milling with a constant material removal rate (MRR). For samples with vertical thin walls, the parameters of waviness (Wa, Wz,) and roughness (Ra, Rz) were measured using a contact profilometer in the selected areas on both processed sides. Deformations were determined in selected cross-sections perpendicular and parallel to the bottom of the sample using GOM measurement (GOM—Global Optical Measurement). The experiment showed the possibility of measuring deformations and deflection arrows of thin-walled elements proceeded from titanium alloy using GOM measurement. Differences in selected surface topography parameters and deformations were observed for the machining methods used with an increased cross-section of the cut layer. A sample with a deviation of 0.08 mm from the assumed shape was obtained.

show abstract

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

et al. 2023

View full text Add to dashboard Cite

show abstract

“… A literature review seems to show insufficient attention to thin-walled structures in the horizontal orientation. Most papers deal with such structures in the vertical orientation [ 8 , 32 , 33 , 34 , 35 , 36 ]. …”

Section: Introductionmentioning

confidence: 99%

Influence of Tools and Cutting Strategy on Milling Conditions and Quality of Horizontal Thin-Wall Structures of Titanium Alloy Ti6Al4V

Kurpiel,

Cudok,

Zagórski

et al. 2023

Sensors

View full text Add to dashboard Cite

Titanium and nickel alloys are used in the creation of components exposed to harsh and variable operating conditions. Such components include thin-walled structures with a variety of shapes created using milling. The driving factors behind the use of thin-walled components include the desire to reduce the weight of the structures and reduce the costs, which can sometimes be achieved by reducing the machining time. This situation necessitates, among other things, the use of new machining methods and/or better machining parameters. The available tools, geometrically designed for different strategies, allow working with similar and improved cutting parameters (increased cutting speeds or higher feed rates) without jeopardizing the necessary quality of finished products. This approach causes undesirable phenomena, such as the appearance of vibrations during machining, which adversely affect the surface quality including the surface roughness. A search is underway for cutting parameters that will minimize the vibration while meeting the quality requirements. Therefore, researching and evaluating the impact of cutting conditions are justified and common in scientific studies. In our work, we have focused on the quality characteristics of horizontal thin-walled structures from Ti6Al4V titanium alloys obtained in the milling process. Our experiments were conducted under controlled cutting conditions at a constant value of the material removal rate (2.03 cm3⁄min), while an increased value of the cut layer was used and tested for use in finishing machining. We used three different cutting tools, namely, one for general purpose machining, one for high-performance machining, and one for high-speed machining. Two strategies were adopted: adaptive face milling and adaptive cylindrical milling. The output quantities included the results of acceleration vibration amplitudes, and selected surface topography parameters of waviness (Wa and Wz) and roughness (Ra and Rz). The lowest values of the pertinent quantities were found for a sample machined with a high-performance tool using adaptive face milling. Surfaces typical of chatter vibrations were seen for all samples.

show abstract

“…The authors of [19] analyzed the deviations of vertical thin-walled parts made from EN AW7075-T651 aluminum alloy using conventional milling and high-speed milling for finishing. The result of their research was a measurement of deviations made using a coordinate measuring machine.…”

Section: Introductionmentioning

confidence: 99%

Dimensional Deviations of Horizontal Thin Wall of Titanium Alloy Ti6Al4V Determined by Optical and Contact Methods

Kurpiel,

Zagórski,

Cieślik

et al. 2023

Materials

View full text Add to dashboard Cite

Thin-walled structures are used in many industries. The need to use such elements is dictated by the desire to reduce the weight of the finished product, as well as to reduce its cost. The most common method of machining such elements is the use of milling, which makes it possible to make a product of almost any shape. However, several undesirable phenomena occur during the milling of thin-walled structures. The main phenomenon is a deformation of the thin wall resulting from its reduced stiffness. Therefore, it is necessary to control the dimensional and shape accuracy of finished products, which is carried out using various measuring instruments. The development of newer measuring methods such as optical methods is being observed. One of the newer measuring machines is the 3D optical scanner. In the present experiment, thin-walled samples in horizontal orientation of Ti6Al4V titanium alloy were machined under controlled cutting conditions. During machining, the cutting speed and feed rate were assumed constant, while the input factors were the tool and cutting strategy. This paper presents graphs of deviations in the determined cross-section planes of thin-walled structures using a 3D optical scanner and a coordinate measuring machine. A correlation was made between the results obtained from the measurement by the optical method and those determined by the contact method. A maximum discrepancy of about 8% was observed between the methods used.

show abstract

Effect of the Geometry of Thin-Walled Aluminium Alloy Elements on Their Deformations after Milling

Cited by 14 publications

References 46 publications

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Investigation of Selected Surface Topography Parameters and Deformation during Milling of Vertical Thin-Walled Structures from Titanium Alloy Ti6Al4V

Influence of Tools and Cutting Strategy on Milling Conditions and Quality of Horizontal Thin-Wall Structures of Titanium Alloy Ti6Al4V

Dimensional Deviations of Horizontal Thin Wall of Titanium Alloy Ti6Al4V Determined by Optical and Contact Methods

Contact Info

Product

Resources

About