EMC Qualification Methodology for Semicustom Digital Integrated Circuit Design

Huynh, Hai Au; Jo, Jeong-Min; Nah, Wansoo; Kim, Soyoung

doi:10.1109/temc.2016.2561978

Cited by 6 publications

(3 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The top level requirements for engine operation equipment EMC design shall be verified by MOC9 [6]，as defined in the following table 1 [7].…”

Section: Top-level Work Of Compatibility Of Electromagnetic Compatibi...mentioning

confidence: 99%

Design and verification for civilian airborne engine operation equipment’s electromagnetic compatibility

Lang,

Liu,

Zheng

et al. 2024

Ninth International Conference on Energy Materials and Electrical Engineering (ICEMEE 2023)

View full text Add to dashboard Cite

Electromagnetic compatibility is very important to Civilian airborne engine operation equipment development. This paper introduces how to define the requirements for electromagnetic compatibility and corresponding verification. The detailed method for how to verify these requirements, especially the qualification test method and test results are shown in this paper. This paper introduces how to improve the technical proposal to resolve the problems caused by qualification test failure which means the verification to some electromagnetic compatibility requirement fails. Final conclusion for design and verification will be provided in the end.

show abstract

“…The top level requirements for engine operation equipment EMC design shall be verified by MOC9 [6]，as defined in the following table 1 [7].…”

Section: Top-level Work Of Compatibility Of Electromagnetic Compatibi...mentioning

confidence: 99%

Design and verification for civilian airborne engine operation equipment’s electromagnetic compatibility

Lang,

Liu,

Zheng

et al. 2024

Ninth International Conference on Energy Materials and Electrical Engineering (ICEMEE 2023)

View full text Add to dashboard Cite

show abstract

“…By using the proposed method, it is expected that the time and cost expense of setting up the test setup, as well as the testing procedure for the conventional measurement-based CS testing, will be drastically reduced. In addition, the proposed method can be used to estimate the conducted immunity of a system in the early stage of the design cycle prior to production.Recently, to overcome the inefficiencies, numerous simulation-based IC-level immunity testing methods for a single IC have been proposed [3][4][5][6][7][8]. To predict the immunity of a victim IC to the conducted noise, the simulation-based testing methods commonly employ the equivalent circuit models for the components.…”

mentioning

confidence: 99%

“…Recently, to overcome the inefficiencies, numerous simulation-based IC-level immunity testing methods for a single IC have been proposed [3][4][5][6][7][8]. To predict the immunity of a victim IC to the conducted noise, the simulation-based testing methods commonly employ the equivalent circuit models for the components.…”

mentioning

confidence: 99%

Simulation-Based System-Level Conducted Susceptibility Testing Method and Application to the Evaluation of Conducted-Noise Filters

et al. 2019

View full text Add to dashboard Cite

In this paper, a simulation-based system-level conducted susceptibility (CS) testing method for a wireless power transfer (WPT) system is proposed. The proposed method employs 3-dimensional electromagnetic (3D EM) models as well as equivalent circuit models to replace the measurement-based CS testing method based on the International Electrotechnical Commission 61000-4-6 standard. The conducted-noise source and equipment under test (EUT) are modeled in a circuit simulator. The conduction path, bulk current injection probe, and calibration jig are modeled using the 3D field simulator. A simple WPT system is designed and fabricated as the EUT for the CS test. The proposed method is successfully verified by comparing the voltage waveforms with measurement-based CS testing method. Additionally, as an application of the proposed method, a simulation-based evaluation of the conducted-noise filters is conducted. By using the proposed method, it is expected that the time and cost expense of setting up the test setup, as well as the testing procedure for the conventional measurement-based CS testing, will be drastically reduced. In addition, the proposed method can be used to estimate the conducted immunity of a system in the early stage of the design cycle prior to production.

show abstract

Simulation-based conducted susceptibility testing for wireless power transfer (WPT) systems

Joo

Song

Kwak

et al. 2018

2018 IEEE International Symposium on Electromagnetic Compatibility and 2018 IEEE Asia-Pacific Symposium on Electromagnetic Comp

View full text Add to dashboard Cite

EMC Qualification Methodology for Semicustom Digital Integrated Circuit Design

Cited by 6 publications

References 20 publications

Design and verification for civilian airborne engine operation equipment’s electromagnetic compatibility

Design and verification for civilian airborne engine operation equipment’s electromagnetic compatibility

Simulation-Based System-Level Conducted Susceptibility Testing Method and Application to the Evaluation of Conducted-Noise Filters

Simulation-based conducted susceptibility testing for wireless power transfer (WPT) systems

Contact Info

Product

Resources

About