Estimation of the Possibilities for Using the Solid Hydrocarbon Fuels in Autophage Launch Vehicle

et al. 2021

EEJET

This paper has investigated the possibility to theoretically calculate a value of the specific impulse for highly energetic compositions using only two parameters – the heat of the reaction and the number of moles of gaseous decomposition reaction products. Specific impulse is one of the most important energetic characteristics of rocket propellant. It demonstrates the level of achieving the value of engine thrust and propellant utilization efficiency. Determining the specific impulse experimentally is a complex task that requires meeting special conditions. For the stage of synthesis of new promising components, the comparative analysis of energetic characteristics, forecasting the value of specific impulse, especially relevant are calculation methods. Most of these methods were first developed to determine the energetic characteristics of explosives. Since explosives and rocket propellants in many cases have similar energy content and similar chemical composition, some estimation methods can be used to assess the specific impulse of solid rocket propellant. The specific impulse has been calculated for 45 compositions based on environmentally friendly oxidizers (ammonium dinitramide, hydrazinium nitroformate, hexanitrohexaazaisowurtzitane) and polymer binders polybutadiene with terminal hydroxyl groups, glycidylazide polymer, poly-3-nitratomethyl-3-methyloxetane). It was established that the estimation data obtained correlate well with literary data. Deviation of the derived values of the specific impulse from those reported in the literature is from 0.4 % to 1.8 %. The calculation results could be used for preliminary forecasting of energetic characteristics for highly energetic compositions, selecting the most promising components, as well as their ratios.

Section: Discussion Of Results From Determining the Energetic Characteristics And Choosing The Environmentally Friendly Components Of Solmentioning

confidence: 99%

“…Also promising are autophage CRs, which use tank shells made of synthetic polymers [1][2][3][4][5][6][7] as fuel.…”

Section: Introductionmentioning

confidence: 99%

Determining energetic characteristics and selecting environmentally friendly components for solid rocket propellants at the early stages of design

Kositsyna

Varlan

et al. 2021

EEJET

“…Works [17,18] report the results of testing an auto-phase JPS. Research is also underway to find the optimal chemical composition of fuel for the autophase launch vehicles [19].…”

Section: Literature Review and Problem Statementmentioning

confidence: 99%

Development of the combined method to de-orbit space objects using an electric rocket propulsion system

Golubek

Dubovik

et al. 2020

EEJET

A method has been developed for the combined de-orbiting of large-size objects of space debris from low-Earth orbits using an electro-rocket propulsion system as an active de-orbiting means. A principal de-orbiting technique has been devised, which takes into consideration the patterns of using an electric rocket propulsion system in comparison with the sustainer rocket propulsion system. A procedure for determining the parameters of the de-orbiting scheme has been worked out, such as the minimum total speed and the time of the start of the de-orbiting process, which ensures its achievement. The proposed procedure takes into consideration the impact exerted on the process of the de-orbiting by the ballistic factor of the object, the height of the initial orbit, and the phase of solar activity at the time of the de-orbiting onset. The actual time constraints on battery discharge have been accounted for, as well as on battery charge duration, and active operation of the control system. The process of de-orbiting a large-size object of space debris has been simulated by using the combined method involving an electro-rocket propulsion system. The impact of the initial orbital altitude, ballistic coefficient, and the phase of solar activity on the energy costs of the de-orbiting process have been investigated. The dependences have been determined of the optimal values of a solar activity phase, in terms of energy costs, at the moment of the de-orbiting onset, and the total velocity, required to ensure the de-orbiting, on the altitude of the initial orbit and ballistic factor. These dependences are of practical interest in the tasks of designing the means of the combined de-orbiting involving an electric rocket propulsion system. The dependences of particular derivatives from the increment of a velocity pulse to the gain in the ballistic factor on the altitude of the initial orbit have been established. The use of these derivatives is also of practical interest to assess the effect of unfolding an aerodynamic sailing unit

“…In the works of (Gobbo-Ferreira et al, 1999;Yemets et al, 2019) it is shown that polyethylene can be used as a fuel in solid-propellant rocket engines. The use of plastic polymer fuels simplifies the design and removes the mass limitation on oxidizer reserves.…”

Section: Introductionmentioning

confidence: 99%

A simulation of the thermal environment of a plastic body of a new type of launch vehicle at the atmospheric phase of the trajectory

Dreus

Yemets

et al. 2021

AEAT

Purpose Leading developers and providers in the modern space launch market note a splash in the development of ultralight launch vehicle (LV), driven by the growing demand for small satellites for large constellations in low Earth orbits. One of the promising ways to solve the problem of the quick launch of such satellites is to use a new type of ultralight launch vehicle with a plastic body. The project of such a launch vehicle was proposed by Oles Honchar Dnipro National University (Ukraine). Along with that, there is a need for appropriate research studies on the thermal resistance of the plastic shell, as the physical, mechanical and thermophysical characteristics of polymers significantly differ from traditional aerospace materials. The purpose of this study is to validate the design and ballistic parameters of such a launch vehicle in terms of providing an acceptable thermal environment at the atmospheric phase of the trajectory. Design/methodology/approach The workability of a new type of propulsion system is being investigated experimentally in bench conditions. To study the process of aerodynamic heating of a plastic shell, numerical modeling based on the integration of the flight dynamics and heat transfer equations is used. Findings Brief information about the design of a new type of ultra-light autophage launch vehicle with a plastic body is presented. A mathematical model for the movement of the launch vehicle at the atmospheric phase of the trajectory, and for the heating of the polyethylene body of the launch vehicle, taking into account the dynamic change in the atmospheric parameters is proposed. The influence of the motion trajectory on the thermal environment of the rocket body is investigated, rational motion trajectories and corresponding permissible g-loads are determined. Originality/value The fundamental possibility of using plastic (polyethylene) as a structural material and fuel for bodies of a new type of ultralight launch vehicles has been substantiated. It is shown that to ensure acceptable thermal conditions of a plastic body, it is necessary to use thermal insulation. It is proposed to use a polymeric Teflon coating as such thermal insulation. The results are important for the development of technologies for launching small satellites into orbit, as the use of plastic as the main structural material of the rocket body will significantly reduce the launch cost.