Exceptional mechanical properties and wear behavior of Al2O3 nanoparticle reinforced Ni-W-P coatings

Kousar, Humaira; Umer, Malik Adeel; Shehzad, Khuram; Ferdous, Rabeeka; Mehmood, Kashif; Basit, Abdul; Shahbaz, Tauheed; Yasir, Muhammad; Shakoor, Abdul

doi:10.1016/j.triboint.2024.109533

Cited by 7 publications

(1 citation statement)

References 40 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…During abrasive wear, the asperities act as abrasives, exerting localized pressure on the coating surface. Abrasive wear results in the formation of grooves, scratches, or patches on the surface of the material, ultimately leading to dimensional changes, loss of material, and degradation of the surface finish of the coating (figure 9(e)) [52,53].…”

Section: Worn Surface Analysismentioning

confidence: 99%

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Akhil,

Radhika,

Jeyaprakash

et al. 2024

Phys. Scr.

View full text Add to dashboard Cite

In the present work, a low-carbon steel substrate was coated with Al2O3 and TiC using self-propagating high temperature synthesis. The synthesized coatings were annealed at 450oC for 2-6 hrs. The characteristics of the substrate, coated, and annealed samples were examined, including microhardness, wear resistance, and corrosion resistance. A pin-on-disc tribometer was employed to conduct the wear test by varying the load, sliding velocity, and distance. The impact of these factors on the wear rate and worn surface morphology was then examined. Further, corrosion resistance was evaluated using electrochemical corrosion testing with 3.5 wt.% NaCl as electrolyte. Results showed that Al2O3 and TiC specimens annealed at 450oC for 5 hrs and 4 hrs improved the microhardness by 1.3 and 1.06 times than that of as-coated specimens respectively. The synthesized Al2O3 and TiC coatings showed an abrasive wear mechanism at higher loads and tribolayer formation was observed at higher sliding velocity and distances. The corrosion and wear resistances of the samples were found as follows: substrate< Al2O3 coated < TiC coated < Al2O3 annealed < TiC annealed. The Al2O3 and TiC ceramic coatings were found to improve wear and corrosion resistance having potential applications in cement, petrochemical, and marine industries.

show abstract

Section: Worn Surface Analysismentioning

confidence: 99%

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Akhil,

Radhika,

Jeyaprakash

et al. 2024

Phys. Scr.

View full text Add to dashboard Cite

show abstract

Tribological and mechanical properties improvement of G20CrNiMo alloy via fabricating gradient composite layer through ultrasonic strengthening grinding process

Xiao,

Zhang,

Lin

et al. 2024

Materials Today Communications

View full text Add to dashboard Cite

Microstructure and wear-resistant behaviors of Al2O3-TiO2 reinforced Ni-based composite coating plasma-sprayed on 6061 aluminum alloy

Yu,

Jiang,

Gao

et al. 2024

Surface and Coatings Technology

View full text Add to dashboard Cite

Exceptional mechanical properties and wear behavior of Al2O3 nanoparticle reinforced Ni-W-P coatings

Cited by 7 publications

References 40 publications

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Tribological and mechanical properties improvement of G20CrNiMo alloy via fabricating gradient composite layer through ultrasonic strengthening grinding process

Microstructure and wear-resistant behaviors of Al2O3-TiO2 reinforced Ni-based composite coating plasma-sprayed on 6061 aluminum alloy

Contact Info

Product

Resources

About

Exceptional mechanical properties and wear behavior of Al2O3 nanoparticle reinforced Ni-W-P coatings

Cited by 7 publications

References 40 publications

Wear and corrosion resistance of Al2O3 and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Wear and corrosion resistance of Al2O3 and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Tribological and mechanical properties improvement of G20CrNiMo alloy via fabricating gradient composite layer through ultrasonic strengthening grinding process

Microstructure and wear-resistant behaviors of Al2O3-TiO2 reinforced Ni-based composite coating plasma-sprayed on 6061 aluminum alloy

Contact Info

Product

Resources

About

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method

Wear and corrosion resistance of Al₂O₃ and TiC deposition on steel substrate using self- propagating high temperature synthesis method