Exergetic assessment of transmission-concentrated solar energy systems via optical fibres for building applications

Zidani, Chafi ka; Benyoucef, B.; Madini, Nassima

doi:10.1504/ijex.2012.049744

Cited by 6 publications

(3 citation statements)

References 14 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…After this, the receiver goes into sleep mode. When an interrupt signal is received, generated every second by the RTC 5), LED (6), diode (7), oxide semiconductor capacitor (8), RTC chip (9), quartz resonator RTC (10), tuning capacitor (11), button to turn on/off mode of generating IR pulses for polling sensors (12), receiver radio module (13), and microcontroller platform Arduino nano (14).…”

Section: Description Of the Receiving Part Of The Data Acquisition Sy...mentioning

confidence: 99%

“…Figure 12. Appearance of DAS receiver removed from case: LCD (1), buzzer (2), USB cable (3), resistor (4), backup battery for powering RTC (5), LED(6), diode(7), oxide semiconductor capacitor (8), RTC chip (9), quartz resonator RTC(10), tuning capacitor(11), button to turn on/off mode of generating IR pulses for polling sensors(12), receiver radio module(13), and microcontroller platform Arduino nano(14).…”

mentioning

confidence: 99%

See 1 more Smart Citation

Wireless Data Acquisition System with Feedback Function

Manukovsky,

Sagyndyk,

Kislov

et al. 2024

Applied Sciences

View full text Add to dashboard Cite

When operating solar–wind power plants (SWPPs) located in populated areas, cases of premature failure of expensive batteries and other power equipment often occur. The purpose of this study is to develop a wireless data acquisition system (DAS) for the operation of an SWPP with a feedback function to prevent material damage from the failure of power equipment and to increase the efficiency of natural energy use. The principles of constructing a DAS, free from some of the disadvantages of analogues, are described in this paper. Intelligent wireless current and voltage sensors and a device for receiving and recording data with an additional feedback function have been developed, providing real-time feedback when the measured parameters go outside the norm. Measurement data are displayed on the laptop screen and alphanumeric display and stored on the hard drive along with timestamps and current event messages. An example of using a reverse communication channel to implement the functions of backup battery protection and to switch SWPP loads is described. The principles and methods proposed in this article are suitable for constructing systems for remote measurements of any physical quantities; therefore, the scope of application of the described system can be significantly expanded.

show abstract

Section: Description Of the Receiving Part Of The Data Acquisition Sy...mentioning

confidence: 99%

mentioning

confidence: 99%

Wireless Data Acquisition System with Feedback Function

Manukovsky,

Sagyndyk,

Kislov

et al. 2024

Applied Sciences

View full text Add to dashboard Cite

show abstract

“…The optical loss of plastic fiber and glass fiber was relatively large with 0.15/m dB by contrast, which had some limitations in the distance of optical transmission. But plastic fiber was easy to make into the transfer beam of large diameter to obtain greater luminous flux and high concentrating rate, which now had a wide range of applications [18]. We chosen quartz optical fiber in the study.…”

Section: Materials and Components Of Solar Optical Fiber Lightingmentioning

confidence: 99%

Design of Solar Optical Fiber Lighting System for Enhanced Lighting in Highway Tunnel Threshold Zone: A Case Study of Huashuyan Tunnel in China

Qin

Zhang

Qi³

et al. 2015

International Journal of Photoenergy

View full text Add to dashboard Cite

In this paper, the principle, structural composition, materials, and characteristics of solar optical fiber lighting system were discussed. The different luminance requirements of different zones of highway tunnel were identified on the basis of the analysis of tunnel lighting considering drivers’ visually self-accommodating physiological function for luminance change. Taken Huashuyan Tunnel of G109 Highway located in Hohhot of Inner Mongolia in China as the case study, the system design of solar optical fiber lighting for enhanced lighting in threshold zone of highway tunnel was made. It was indicated through calculation that the design length of solar optical fiber enhanced lighting was related to the design speed, longitudinal slope, and overhead clearance of the tunnel, and the design luminance of solar optical fiber enhanced lighting was related to the luminance outside the tunnel, the design speed, and the design traffic flow of the tunnel. Luminance analysis of the solar optical fiber lighting system of Huashuyan Tunnel was made based on the on-site experiment. Also, the 3D illuminance simulation results by DIALux software were made to indicate that the solar optical fiber lighting system in Huashuyan Tunnel still well met the enhanced lighting demand even not considering the contribution of LED lighting.

show abstract