Experimental Investigations on Machinability of Aluminium Alloy (A413)/Flyash/B4C Hybrid Composites Using Wire EDM

Prakash, J. Udaya; Moorthy, T.V.; Peter, Josephine

doi:10.1016/j.proeng.2013.09.216

Cited by 55 publications

(22 citation statements)

References 10 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Prakash et al [12] used L27 orthogonal array to conduct the experiments and ANOVA to determine the significance of process parameters on the output response. Puhan et al [13] investigated the influence of process parameters on multiple performance characteristics in EDM of Aluminium Composites.…”

Section: Introductionmentioning

confidence: 99%

Investigation of EDM Process parameters for Hybrid Metal Matrix Composites

Maniyar

Ingole²

2018

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

Abstract. The goal of present research work is to investigate the Electrical discharge Machining process parameters namely current, pulse on time and combined equal weight percentage of silicon carbide and graphite on material removal rate, tool wear rate and surface roughness of hybrid metal matrix composites. Experimental trails are done by Taguchi's L27 orthogonal array. Signal to noise ratio is used to determine optimal setting of process parameters. Analysis of Variance is utilized to discover the most influential machining process parameters on output responses. This examination have shown results of ideal machining condition which can be utilized to boost material removal rate as well as to limit tool wear rate and surface roughness. Finally results are validated by confirmation Tests.

show abstract

Section: Introductionmentioning

confidence: 99%

Investigation of EDM Process parameters for Hybrid Metal Matrix Composites

Maniyar

Ingole²

2018

IOP Conf. Ser.: Mater. Sci. Eng.

View full text Add to dashboard Cite

show abstract

“…Abrasion was found to be the dominant wear mechanism from the experimental study. Udaya Prakash et al (2013) investigated the effect of parameters like gap voltage, pulse on time, pulse off time, wire feed and percentage of reinforcement on the response material removal rate as well as surface roughness while machining Al413/fly ash/boron carbide hybrid composite using wire electrical discharge machining. Shanmugha Sundaram and Subramanian (2013) experimentally investigated on the surface roughness of pure commercial Al, Al-15 wt% fly ash, and Al-15 wt% fly ash/1.5 wt% graphite (Gr) composites produced by modified two-step stir casting.…”

Section: Introductionmentioning

confidence: 99%

Multi-regression prediction model for surface roughness and tool wear in turning novel aluminum alloy (LM6)/fly ash composite using response surface and central composite design methodology

Panda¹,

Senapati²,

Mishra³

2017

10.5267/j.ijiec

View full text Add to dashboard Cite

Turning experiments were conducted on a novel aluminum alloy (LM6)/fly ash composite based on the response surface and face centered central composite design methodology. The effects of cutting parameters on surface roughness and tool wear were investigated. Multiple regression models were developed for the responses and the adequacies of the developed models were tested at 95% confidence interval using the analysis of variance (ANOVA) technique. Carbide inserts (Model: CNMG 120408-M5) were used for turning the specimens in a CNC turning machine (model: LT-16). The test for significance of the regression models, the test for significance on individual model coefficients and the lack-of-fit tests were performed using the statistical Design-Expert7.0v software environments. R2 indicated the model significance and the value was more than 97%, revealed that the relation between cutting responses and input parameters held good for more than 97% and the model was adequate.

show abstract

“…[8][9][10][11][12][13][14]. This paper deals with the machinability and optimization of 413/B 4 C composites.…”

Section: Introductionmentioning

confidence: 99%

Optimization of Wire EDM Process Parameters for Machining of AMCs (413/B4c) using Taguchi Technique

al.¹

2017

IJMPERD

View full text Add to dashboard Cite

Experimental Investigations on Machinability of Aluminium Alloy (A413)/Flyash/B4C Hybrid Composites Using Wire EDM

Cited by 55 publications

References 10 publications

Investigation of EDM Process parameters for Hybrid Metal Matrix Composites

Investigation of EDM Process parameters for Hybrid Metal Matrix Composites

Multi-regression prediction model for surface roughness and tool wear in turning novel aluminum alloy (LM6)/fly ash composite using response surface and central composite design methodology

Optimization of Wire EDM Process Parameters for Machining of AMCs (413/B4c) using Taguchi Technique

Contact Info

Product

Resources

About