Facile preparation and tribological property of alloyed Fe3Si coatings on stainless steels surface by molten-salt infiltration method

Tang, Changbin; Chen, Hongxia; Wen, Fu-rong; Xu, Nanping; Huang, Wei; Xue, Juanqin

doi:10.1016/j.surfcoat.2020.126049

Cited by 10 publications

(6 citation statements)

References 25 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Hirakawa et al [14] and C.B. Tang et al [26,27]. For the details, the orientation of Fe 3 Si(222) denoted that the films hold a B 2 structure with a superlattice reflection of B 2 -Fe 3 Si crystallites [5].…”

Section: Investigation Of the Properties Of Fe 3 Si Filmsmentioning

confidence: 99%

Physical Properties of Fe3Si Films Coated through Facing Targets Sputtering after Microwave Plasma Treatment

et al. 2021

View full text Add to dashboard Cite

Fe3Si films are deposited onto the Si(111) wafer using sputtering with parallel facing targets. Surface modification of the deposited Fe3Si film is conducted by using a microwave plasma treatment under an Ar atmosphere at different powers of 50, 100 and, 150 W. After the Ar plasma treatment, the crystallinity of the coated Fe3Si films is enhanced, in which the orientation peaks, including (220), (222), (400), and (422) of the Fe3Si are sharpened. The extinction rule suggests that the B2–Fe3Si crystallites are the film’s dominant composition. The stoichiometry of the Fe3Si surfaces is marginally changed after the treatment. An increase in microwave power damages the surface of the Fe3Si films, resulting in the generation of small pinholes. The roughness of the Fe3Si films after being treated at 150 W is insignificantly increased compared to the untreated films. The untreated Fe3Si films have a hydrophobic surface with an average contact angle of 101.70°. After treatment at 150 W, it turns into a hydrophilic surface with an average contact angle of 67.05° because of the reduction in the hydrophobic carbon group and the increase in the hydrophilic oxide group. The hardness of the untreated Fe3Si is ~9.39 GPa, which is kept at a similar level throughout each treatment power.

show abstract

Section: Investigation Of the Properties Of Fe 3 Si Filmsmentioning

confidence: 99%

Physical Properties of Fe3Si Films Coated through Facing Targets Sputtering after Microwave Plasma Treatment

et al. 2021

View full text Add to dashboard Cite

show abstract

“…At 600 °C, Si(111) and β (021) continually intensify with the increasing temperature while Fe 3 Si(222) and Fe 3 Si(422) are replaced with Fe 3 Si(220) at 45.34° as depicted in Fig. 1 b [ 8 , 23 ]. Orientation peaks of (111) and (211) of FeSi also appear at 34.76° and 49.99° [ 24 ].…”

Section: Resultsmentioning

confidence: 99%

“…Furthermore, they possess noticeable thermal stability beyond temperatures of 800 K Curie [ [4] , [5] , [6] ]. The Fe 3 Si films enjoy a high degree of hardness and corrosion resistance [ 7 , 8 ]. Hence, our research group studied the structural and magnetic attributes of Fe 3 Si films and reported them in our former works [ [9] , [10] , [11] ].…”

Section: Introductionmentioning

confidence: 99%

Wetting state and mechanical property alteration for the Fe3Si films using rapid thermal annealing under various temperatures

Borwornpornmetee,

Traiprom,

Kusaba

et al. 2023

Heliyon

View full text Add to dashboard Cite

“…The addition of Cr to steel can strongly improve its heat-resistance and corrosionresistance [6][7][8][9][10][11][12], and the addition of Si to Fe and Fe-Cr steels results in the enhancement of a SiO 2 protective layer on the surface, thus greatly enhancing the high-temperature oxidation resistance [13,14]. Fe-Cr-Si alloy material has metal silicides represented by Fe3Si, which has characteristics such as high hardness, strong interatomic bonding and good wear resistance [15][16][17]. Yuan and Wang [18] prepared an α/Fe 9 Cr 9 Si 2 ternary metal silicide alloy, which had a low coefficient of friction under dry sliding friction conditions.…”

Section: Introductionmentioning

confidence: 99%

Effect of Temperature and Load on Tribological Behavior in Laser-Cladded FeCrSiNiCoC Coatings

Long

et al. 2023

Materials

View full text Add to dashboard Cite

The FeCrSiNiCoC coatings with fine macroscopic morphology and uniform microstructure were made on 1Cr11Ni heat resistant steel substrate by a laser-based cladding technique. The coating consists of dendritic γ-Fe and eutectic Fe-Cr intermetallic with an average microhardness of 467 HV0.5 ± 22.6 HV0.5. At the load of 200 N, the average friction coefficient of the coating dropped as temperature increased, while the wear rate decreased and then increased. The wear mechanism of the coating changed from abrasive wear, adhesive wear and oxidative wear to oxidative wear and three-body wear. Apart from an elevation in wear rate with increasing load, the mean friction coefficient of the coating hardly changed at 500 °C. Due to the coating’s transition from adhesive wear and oxidative wear to three-body wear and abrasive wear, the underlying wear mechanism also shifted.

show abstract

Facile preparation and tribological property of alloyed Fe3Si coatings on stainless steels surface by molten-salt infiltration method

Cited by 10 publications

References 25 publications

Physical Properties of Fe3Si Films Coated through Facing Targets Sputtering after Microwave Plasma Treatment

Physical Properties of Fe3Si Films Coated through Facing Targets Sputtering after Microwave Plasma Treatment

Wetting state and mechanical property alteration for the Fe3Si films using rapid thermal annealing under various temperatures

Effect of Temperature and Load on Tribological Behavior in Laser-Cladded FeCrSiNiCoC Coatings

Contact Info

Product

Resources

About