Fatigue of a 3D Orthogonal Non-crimp Woven Polymer Matrix Composite at Elevated Temperature

Wilkinson, Michael; Ruggles‐Wrenn, M. B.

doi:10.1007/s10443-017-9597-5

Cited by 14 publications

(6 citation statements)

References 29 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The tension-tension fatigue properties of this typical composites measured for both on-axis (0/90) and off-axis (±45) fiber orientations at elevated temperature (T right = 329 °C) in laboratory air [63]. For the 0/90 fiber orientation, the fatigue run-out of 2 × 10 5 cycles was achieved at 64% UTS.…”

Section: Fatigue Testing Methodsmentioning

confidence: 99%

Review on the fatigue properties of 3D woven fiber/epoxy composites: testing and modelling strategies

Zhang

Zhu

2020

Journal of Industrial Textiles

View full text Add to dashboard Cite

3D woven fiber/epoxy composites as structural components have attracted great attention in the industrial and civil fields due to high resistance to debonding or delamination. Structural components are often subjected to the conditions of cyclic loading, which detrimentally affect the service-life and damage tolerance. In this research, the fatigue properties of 3D woven fiber/epoxy structural composites were discussed, where 3D woven fabrics were embedded in epoxy matrix to enhance their mechanical properties. 3D woven fabrics were classified by the geometrical structures of repeat vertical and inclined units. Based on the testing method, the fatigue properties of corresponding composites have been reviewed. The influence of the internal and external parameters on the fatigue properties were investigated by using various observation methods, and the failure modes were also analyzed. The theorical prediction models were reviewed according to testing method, and future trends and challenges were discussed. The critical review can provide valuable ideas and guidance for future fatigue studies in 3D woven composites.

show abstract

Section: Fatigue Testing Methodsmentioning

confidence: 99%

Review on the fatigue properties of 3D woven fiber/epoxy composites: testing and modelling strategies

Zhang

Zhu

2020

Journal of Industrial Textiles

View full text Add to dashboard Cite

show abstract

“…In particular, because PI fibers can be used within a wide range of temperatures, they match well with the ultrahigh temperature and pressure applied in the processing conditions of high performance resins and achieve long-term service stability under extreme environments. [6][7][8][9][10][11][12][13][14] In addition, the low dielectric constant and loss of PI fibers also make them a promising substance in the manufacturing of structural-functional integration materials for wavetransparent applications, such as in the radomes of satellite or 5G base stations, providing a new approach to the material design and selection of advanced composites. [15][16][17][18] At present, the primary problem of applying PI resins prepared using a polymerization monomeric reactant (PMR) method is the difficulty in molding.…”

Section: Introductionmentioning

confidence: 99%

Polyimide fabric-reinforced polyimide matrix composites with excellent thermal, mechanical, and dielectric properties

Pan

Han

Wang

et al. 2020

High Performance Polymers

View full text Add to dashboard Cite

Two types of thermosetting polyimide (PI) resin were prepared using a polymerization monomeric reactant method, and high performance PI fabric/PI resin composites were fabricated through a wet infiltration and thermoforming process. The properties of a PI fabric, PI resin, and PI/PI composites were comprehensively analyzed. The experimental results indicate that a resin end-capped with phenylacetylene achieves a better processability and heat resistance. The two composites exhibit excellent thermal, mechanical, and dielectric properties. They achieve a glass transition temperature of higher than 320°C and a 5% weight loss temperature of over 600°C under an air atmosphere. During mechanical testing, an interlaminar shear strength exceeding 35 MPa was achieved, whereas the maximum flexural strength was found to be greater than 400 MPa. Moreover, their dielectric constant at 1 MHz was below 3.4, with a dielectric loss of no more than 0.01.

show abstract

“…Recently, the mechanical behavior of the typical textile composites and MWC attracts more interests. [7][8][9][10] Ma et al 11 investigated the classification and properties of three-dimensional (3D) textile fabrics, which are used as the reinforcing phase in textile structural composites, and their geometry affects the physical and mechanical properties of composites. Wilkinson et al 9 investigated the tension-tension fatigue behavior of polymer matrix composite at elevated temperatures.…”

Section: Introductionmentioning

confidence: 99%

“…[7][8][9][10] Ma et al 11 investigated the classification and properties of three-dimensional (3D) textile fabrics, which are used as the reinforcing phase in textile structural composites, and their geometry affects the physical and mechanical properties of composites. Wilkinson et al 9 investigated the tension-tension fatigue behavior of polymer matrix composite at elevated temperatures. The results showed that the elevated temperatures have little effect on the on-axis tensile properties; however, the off-axis tensile strength decreases slightly with the increase in temperature.…”

Section: Introductionmentioning

confidence: 99%

An experimental investigation for the temperature effect on the bending properties of multiaxial warp-knitted composite

Gao

Yang

et al. 2020

Journal of Engineered Fibers and Fabrics

View full text Add to dashboard Cite

An experimental study of bending properties of composites reinforced with triaxial and quadaxial warp-knitted glass fabrics was carried out in the 0°, 45°, and 90° directions at −30°C, 0°C, 20°C, and 40°C, respectively. The relationships between the stress–strain curves, bending strength, bending modulus, and temperature were obtained. The failure mechanisms at different temperatures were also analyzed based on the fracture morphologies and scanning electron microscope (SEM) images. The results indicated that the bending properties decrease slightly with the increase in temperature from −30°C to 20°C and decrease dramatically from 20°C to 40°C. The ultimate bending strength of triaxial and quadaxial warp-knitted composites decreases approximately 31.34% and 34.29%, respectively. In particular, the relationships between bending strength and temperature were also obtained by nonlinear fitting with the experimental data, which could be used to predict the bending behavior at different temperatures.

show abstract

Fatigue of a 3D Orthogonal Non-crimp Woven Polymer Matrix Composite at Elevated Temperature

Cited by 14 publications

References 29 publications

Review on the fatigue properties of 3D woven fiber/epoxy composites: testing and modelling strategies

Review on the fatigue properties of 3D woven fiber/epoxy composites: testing and modelling strategies

Polyimide fabric-reinforced polyimide matrix composites with excellent thermal, mechanical, and dielectric properties

An experimental investigation for the temperature effect on the bending properties of multiaxial warp-knitted composite

Contact Info

Product

Resources

About