Feasibility of improving shear performance of RC pile caps using various internal reinforcement configurations: Tests and finite element modelling

Basha, Ali; Tayeh, Bassam A.; Maglad, Ahmed M.; Mansour, Walid

doi:10.1016/j.engstruct.2023.116340

Cited by 26 publications

(2 citation statements)

References 17 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…and η is a material coefficient. Considering the conclusions from technical reports and experimental and numerical investigations [7,[36][37][38][39][40][41], the fracture energies in both the normal and the shear directions are assumed to be within the range of 300-1500 J/m 2 , while η is set to be 1.45.…”

Section: Cohesive Zone Criterionmentioning

confidence: 99%

Improving the Flexural Response of Timber Beams Using Externally Bonded Carbon Fiber-Reinforced Polymer (CFRP) Sheets

Mansour,

Li,

Wang

et al. 2024

Materials

Self Cite

View full text Add to dashboard Cite

This paper presents a numerical investigation of the flexural behavior of timber beams externally strengthened with carbon-fiber-reinforced polymer (CFRP) sheets. At first, the accuracy of linear elastic and elastic-plastic models in predicting the behavior of bare timber beams was compared. Then, two modeling approaches (i.e., the perfect bond method and progressive damage technique using the cohesive zone model (CZM)) were considered to simulate the interfacial behavior between FRP and timber. The models were validated against published experimental data, and the most accurate numerical procedure was identified and subsequently used for a parametric study. The length of FRP sheets varied from 50% to 100% of the total length of the beam, while different FRP layers were considered. Moreover, the effects of two strengthening configurations (i.e., FRP attached in the tensile zone only and in both the tensile and compressive zones) on load-deflection response, flexural strength, and flexural rigidity were considered. The results showed that elastic-plastic models are more accurate than linear elastic models in predicting the flexural strength and failure patterns of bare timber beams. In addition, with increasing FRP length, the increase in flexural strength ranged from 10.3% to 52.9%, while no further increase in flexural strength could be achieved beyond an effective length of 80% of the total length of the beam. Attaching the FRP to both the tensile and compressive zone was more effective in enhancing the flexural properties of the timber beam than attaching the FRP to the tensile zone only.

show abstract

Section: Cohesive Zone Criterionmentioning

confidence: 99%

Improving the Flexural Response of Timber Beams Using Externally Bonded Carbon Fiber-Reinforced Polymer (CFRP) Sheets

Mansour,

Li,

Wang

et al. 2024

Materials

Self Cite

View full text Add to dashboard Cite

show abstract

“…Sliding shear failure is less common but can occur under certain conditions, such as low compressive stress and high horizontal force, causing damage along a horizontal mortar joint [4]. Non-reversible structural interventions for seismic retrofitting [5][6][7] of reinforced concrete [8][9][10][11][12] are extensively investigated without considering the carbon footprint of these interventions [4,13]. The importance of this topic goes beyond academic study; it has direct implications for building safety and resilience in earthquake-prone areas, with risk assessment methods proposed by different researchers [14,15].…”

Section: Introductionmentioning

confidence: 99%

Comparison Regarding the Carbon Footprint of Various Sustainable Seismic Consolidation Solutions for Romanian Orthodox Churches

Gosta,

Fofiu,

Kirizsan

2024

Sustainability

View full text Add to dashboard Cite

In Romania, there are numerous Orthodox churches, many of which are historical monuments of great cultural value that have suffered multiple degradations over time due to various natural or man-made reasons. In a context that is currently increasingly focused on environmental protection, we aim to analyse the carbon footprint of several different consolidation proposals to an Orthodox church with structural deteriorations (and more) and the equivalent impact if a similar building were erected with new materials. The research is proposed to be a stepping stone for determining the sustainability of interventions for orthodox churches, as the existing literature is scarce when it comes to the emissions of these churches and there is no norm to prevent unsustainable interventions. The Orthodox Church “Sfintii Voievozi”, the subject of the analysis, is in the city of Tg. Jiu, Gorj County. The construction was documented to be between 1748 and 1764 and is a historical monument listed in the LMI GJ-II-m-A-09189 registry. The architectural solutions for the church and the structural elements that comprise the load-bearing system are presented. A detailed investigation was conducted to determine structural and non-structural degradations, specifying the main causes that have produced them. With regard to consolidation solutions, two options are presented and compared in this paper: Alternative I—minimal intervention and Alternative II—maximal intervention, both of which are reversible. The carbon footprint calculation was carried out for both options, determining the associated material consumption, and compared to the carbon footprint for the case of a new construction. In conclusion, the consolidation methods with a minimal degree of intervention is recommended as the “most environmentally friendly”, considering carbon emissions when comparing the options.

show abstract

Restoration of load capacity and stiffness of continuous steel–concrete composite beams having web openings using externally applied FRP strips

Hakeem,

Osama,

et al. 2024

Structural Concrete

View full text Add to dashboard Cite

The aim of this study is to explore the applicability of externally bonded fiber‐reinforced polymer (FRP) composites to enhance the structural performance of steel–concrete composite beams with web openings in terms of load capacity and stiffness. In order to achieve this aim, the ABAQUS software was used to create a three‐dimensional (3D) non‐linear finite element model (FEM) to simulate the behavior of FRP‐strengthened continuous composite beams with web openings exposed to monotonic loadings. After ascertaining the accuracy of the proposed model's results in successfully predicting failure patterns and load capacities of the experimentally tested specimens available in the literature, the suggested model was used to create a parametric study. The parametric study focused on the impacts of the opening location, opening shapes, and opening area on the failure pattern, load carrying capacity, and stiffness of continuous steel–concrete composite beams. Additionally, strengthening the web openings using different configurations and lengths of FRP strips with and without bolts was investigated. Results showed that the presence of web openings in location 2 exhibited the lowest load capacity of all investigated beams (20.80%–42.50% lower than the control composite beam). Moreover, the continuous composite beams with a circular opening were the best case and gave a higher failure load as compared to the rectangular opening at all locations. Additionally, all the simulated FRP‐strengthened composite beams in the third group demonstrated significant values of load capacities and stiffness among all the analyzed specimens.

show abstract

Feasibility of improving shear performance of RC pile caps using various internal reinforcement configurations: Tests and finite element modelling

Cited by 26 publications

References 17 publications

Improving the Flexural Response of Timber Beams Using Externally Bonded Carbon Fiber-Reinforced Polymer (CFRP) Sheets

Improving the Flexural Response of Timber Beams Using Externally Bonded Carbon Fiber-Reinforced Polymer (CFRP) Sheets

Comparison Regarding the Carbon Footprint of Various Sustainable Seismic Consolidation Solutions for Romanian Orthodox Churches

Restoration of load capacity and stiffness of continuous steel–concrete composite beams having web openings using externally applied FRP strips

Contact Info

Product

Resources

About