Features of the Hydratation Processes of Highly Dispersed   Binders

Introduction. The manuscript is devoted to the actual problem of thermal insulation of buildings and structures. The paper presents a developed low-density insulation solution with improved heatengineering characteristics. The aim of the work is to increase the efficiency of the heat-shielding system using a low-density heat-insulating solution.Methods and materials.The authors carried out tests at the site of heat engineering control of LLC «Intellect-service-ZBK-1» to determine the resistance to heat transfer of the enclosing structure.Results.The construction of the wall system consisting of the «Aerobel» D500 gas-silicate block (625×200×250 mm) and made on a low-density heat-insulating masonry mortar, as well as with the use of a heat-insulating mortar and a universal «Moutrical» energy-efficient coating allowed increasing actual reduced heat transfer resistance from 0.9 to 1.4 (m2 ·K) / W (by 36%).Discussion and conclusions.Laboratory research and field tests that meet the requirements of state standards and that develop low-density heat-insulating plaster demonstrate the low-density heatinsulating solution, which indicates the feasibility in thermal insulation of buildings and structures. The authors achieve special economic and ecological effect in connection with the use of local raw materials and waste production of expanded perlite sand.

show abstract

Effective Heat-Protective System With the Use of Thermal Insulating Solution of Reduced Density

Zagorodnyuk

Sumskoy

Zolotykh

2019

Vestn. SibADI

View full text Add to dashboard Cite

show abstract

Polymineral Composite Binders for Foam Concrete: Features of Hydration and Hardening

Voronov

Glagolev

2020

Vestn. SibADI

View full text Add to dashboard Cite

Introduction. The paper devotes to the features of hydration and hardening of polymineral composite binders. The authors carry out the complex research of the phase composition, hydration and structure formation processes of hardened composite binders with active mineral additives by X-ray phase analysis, differential scanning calorimetry and electron microscopy. The study using a Tescan MIRA 3 scanning electron microscope reveals differences in the microstructure of hardened binders and the authors confirm the results by microprobe studies. The authors study the hydration of the composite binder prepared on the basis of Portland cement and mineral components. Moreover, the paper demonstrates the dynamics of the system’s heat dissipation from the moment of mixing with water and hardening up to 24 hours and up to 72 hours by the expressed bond of dQ / dt = f (t) using a differential calorimeter.Methods and materials. The authors carried out experimental studies at Belgorod State Technological University named after V.G. Shukhov, at the Department of Building Materials, Products and Structures, at the High Technology Center and “BelGTASM-Certificate” Test Center. Therefore, the authors used the existing basic research methods, including modern physicochemical methods of analysis: X-ray phase, scanning electron microscopy, etc. The paper determined the main characteristics of raw materials, composite binders and foam concrete using standard methods and regulatory requirements.Results. The authors obtained the results that testified the peculiarities of hydration and hardening processes of polymineral composite binders on the basis of Portland cement and mineral additives: opoka marl and fly ash.Conclusion. The research establishes the hydration and hardening processes of polymineral composite binders. As a result, the authors demonstrate that the opoka marl introduced into the cement leads to the increased hydration in the induction and accelerated periods and also increases the hydration completeness of the main clinker minerals due to the manifestation of the pozzolanic reaction and the active binding of blocking Portlandite, as well as to the higher concentration of accumulated neoplasms, second generation calcium hydrosilicates.Financial transparency: the authors have no financial interest in the presented materials or methods. There is no conflict of interest.

show abstract

Features of the Formation of the Microstructure of Granular Aggregates on Different Binding Compositions

Zagorodnyuk

Ryzhikh

Sumskoy

et al. 2021

Bulletin of Belgorod State Technological University Named After. V. G. Shukhov

View full text Add to dashboard Cite

This work includes a study of the microstructure of granular aggregates prepared on various binding compositions. The presented work includes three parts devoted to the analysis of the microstructures of granular aggregates taking into account the change in the percentage of the mineral filler in binding compositions. The article deals with the main aspects of the formation of the structure of granular aggregates during the hydration of Portland cement (PC 500-D0-N) and a binder composition (PC 500-D0-N + 10 % quartz sand) prepared in a vortex jet mill. The main regularities of the influence and dispersion of quartz mineral filler (fractions ≤0.16; ≤0.315; ≤0.63 mm) on structure formation during the hydration of binding components differing in the composition and particle dispersion are revealed. The paper analyzes physical and mechanical tests of the most promising samples with a study of their microstructure features. The study of the sample microstructures reveals the general regularities of the growth of crystalline phases of different densities. It is established that the introduction of 1 0% mineral fine-dispersed filler, in the form of quartz sand, contributes to the formation of sub-microcrystalline hydrate phases, which are centers of hydration, additionally binding individual grains of granular aggregates and compacting the structure of the overall system. In all samples, the formation of a block-rhythmic structure is observed, with the presence of individual block-aggregates. There is an overgrowth of microscopic pores with small crystalline neoplasms of calcium hydrosilicates. It is revealed that the structure of granular aggregates prepared on the basis of binder composition No. 1 (BK-1) has higher density than on Portland cement PC 500-D0-N.

show abstract

scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.

Contact Info

customersupport@researchsolutions.com

10624 S. Eastern Ave., Ste. A-614

Henderson, NV 89052, USA

This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.

Blog Terms and Conditions API Terms Privacy Policy Contact Cookie Preferences Do Not Sell or Share My Personal Information

Made with 💙 for researchers

Part of the Research Solutions Family.

Features of the Hydratation Processes of Highly Dispersed Binders

Cited by 6 publications

References 0 publications

Effective Heat-Protective System With the Use of Thermal Insulating Solution of Reduced Density

Effective Heat-Protective System With the Use of Thermal Insulating Solution of Reduced Density

Polymineral Composite Binders for Foam Concrete: Features of Hydration and Hardening

Features of the Formation of the Microstructure of Granular Aggregates on Different Binding Compositions

Contact Info

Product

Resources

About