Friction and wear behavior of three-dimensional braided carbon fiber/epoxy composites under dry sliding conditions

Wan, Yizao; Chen, G.C.; Raman, Sudha R.; Xin, Junna; Li, Q.Y.; Huang, Yiping; Wang, Y.L.; Luo, Honglin

doi:10.1016/j.wear.2005.06.007

Cited by 40 publications

(18 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Namely, the wear rates of the composites at elevated temperature above 1808C were much larger than that below 1808C, which was attributed to the degradation and decomposition of the adhesive resin at excessively elevated temperature. Finally, Wan et al [8] investigated the sliding friction and wear characteristics of three-dimensional braided carbon fabric reinforced epoxy resin composites. The test were performed under normal loads of 50, 100, and 150 N and velocities of 0.42 and 0.84 m/s.…”

Section: Journal Of Thermoplastic Composite Materials Vol 21-may 2008mentioning

confidence: 99%

Wear Behavior of a Glass Fiber-Reinforced PEI Composite

Viña

García

Castrillo

et al. 2008

Journal of Thermoplastic Composite Materials

View full text Add to dashboard Cite

The wear behavior of a thermoplastic polymer, polyetherimide, and of a composite with this polymer as matrix and a reinforcement of glass fiber fabric has been analyzed. The test was carried out according to the Standard ASTM G99 using a device pin-on-disk. Obviously, the reinforced material has higher wear strength than the nonreinforced material. Also, the evolution of the wear with the temperature has been studied at ambient temperature and at 50, 100, 150, and 2008C. The effect of the temperature is very important because when it was increased the wear was increased, except to 2008C. At 2008C there was an important decrease. The test temperature was measured in the inner of the furnace and when it was 2008C in this zone, the temperature in the contact point was higher and it would be close to glass transition temperature of the polymer ($2178C), this is the reason for an important micro-structural variation in the material.

show abstract

Section: Journal Of Thermoplastic Composite Materials Vol 21-may 2008mentioning

confidence: 99%

Wear Behavior of a Glass Fiber-Reinforced PEI Composite

Viña

García

Castrillo

et al. 2008

Journal of Thermoplastic Composite Materials

View full text Add to dashboard Cite

show abstract

“…Three-dimensional braided carbon fiber reinforced epoxy (C 3D /EP) composites are excellent materials for surgery or aviation because of their good properties, such as improved overall performance, high strength, desirable modulus, splendid friction and wear characteristics, etc [2,3]. The deposition of some coatings on the surface of C 3D /EP composites will be greatly helpful to their applications.…”

Section: Introductionmentioning

confidence: 99%

Air dielectric barrier discharges plasma surface treatment of three-dimensional braided carbon fiber reinforced epoxy composites

Liang

et al. 2009

Surface and Coatings Technology

View full text Add to dashboard Cite

“…Light weight and longevity are critical to airspace applications of ultrasonic motor; thus, using reinforced composites is a satisfactory option . In addition, carbon‐fiber‐reinforced composites are desirable because of their cost‐effectiveness, superior strength, and stiffness. In general, the orientation sequence of the plies affects the strength and stiffness of composite build‐up.…”

Section: Introductionmentioning

confidence: 99%

Micro‐Driving behavior of carbon‐fiber‐reinforced epoxy resin for standing‐wave ultrasonic motor

Zhang

2015

Polymer Composites

View full text Add to dashboard Cite

The application of the friction drive of carbon-fiberreinforced composites to a standing-wave ultrasonic motor was investigated. Friction drive tests were conducted on carbon-fiber-reinforced epoxy resins (CF/ epoxy) by home-made test rig, which was based on plate-rod vibrator. The effects of fiber orientation and ply thickness on dynamic drive and dynamic normal forces were investigated. Fiber orientation angle and ply thickness affected friction drive. Different dynamic drive forces, which varied both in amplitude and period, were observed for CF/epoxy composites with different winding angles. A CF/epoxy composite with a winding angle of 30 showed the largest dynamic drive force (~0.45 N) and the shortest contact period (~26 ls). The period of dynamic normal force was uniform (~65 ls) for various CF/epoxy composites. Wear traces of different composites exhibited different wear modes, such as scuffing, peeling, and shearing. The anisotropic property of CF/epoxy material affected the drive process of standing-wave ultrasonic motor. The current study taking the carbon-fiber-reinforced epoxy resin as an example of anisotropic materials arise more enough attention on inexpensive, biodegradable, and renewable alternatives for the efficient and durative drive of a standing-wave ultrasonic motor. POLYM. COMPOS.,

show abstract

Friction and wear behavior of three-dimensional braided carbon fiber/epoxy composites under dry sliding conditions

Cited by 40 publications

References 22 publications

Wear Behavior of a Glass Fiber-Reinforced PEI Composite

Wear Behavior of a Glass Fiber-Reinforced PEI Composite

Air dielectric barrier discharges plasma surface treatment of three-dimensional braided carbon fiber reinforced epoxy composites

Micro‐Driving behavior of carbon‐fiber‐reinforced epoxy resin for standing‐wave ultrasonic motor

Contact Info

Product

Resources

About