Functionalization of 3D printed ABS filters with MOF for toxic gas removal

Pellejero, Ismael; Almazan, F.; Lafuente, Marta; Urbiztondo, M.A.; Drobek, Martin; Bechelany, Mikhael; Julbe, A.; Gandı́a, Luis

doi:10.1016/j.jiec.2020.05.013

Cited by 31 publications

(20 citation statements)

References 55 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The MoS 2 coated electrodes were then successfully applied for photoelectrocatalytic hydrogen evolution reaction (HER). Recently the group of M. Bechelany from the Institut Européen des Membranes (IEM, Montpellier, France) has developed in collaboration with the University of Zaragoza the functionalization of 3D printed ABS filters with MOF (Metal-Organic Framework) for toxic gas removal [75]. The fabrication approach at low temperature includes ALD of Zinc oxide on the ABS 3D printed filter followed by the hydrothermal conversion of ZnO to ZIF-8, Zeolitic Imidazolate Framework.…”

Section: Illustration Of the Combination Of 3d Printing And Atomic La...mentioning

confidence: 99%

Nanometric 3D Printing of Functional Materials by Atomic Layer Deposition

Muñoz‐Rojas¹,

Weber²,

Vallée³

et al. 2022

Advanced Additive Manufacturing

Self Cite

View full text Add to dashboard Cite

Atomic layer deposition (ALD) is a chemical vapour deposition (CVD) method that allows the layer-by-layer growth of functional materials by exposing a surface to different precursors in an alternative fashion. Thus, thanks to gas-solid reactions that are substrate-limited and self-terminating, precise control over thickness below the nanometer level can be achieved. While ALD was originally developed to deposit uniform coatings over large areas and on high-aspect-ratio features, in recent years the possibility to perform ALD in a selective fashion has gained much attention, in what is known as area-selective deposition (ASD). ASD is indeed a novel 3D printing approach allowing the deposition of functional materials (for example metals to oxides, nitrides or sulfides) with nanometric resolution in Z. The chapter will present an introduction to ALD, which will be followed by the description of the different approaches currently being developed for the ASD of functional materials (including initial approaches such as surface pre-patterning or activation, and newer concepts based on spatial CVD/ALD). The chapter will also include a brief overview of recent works involving the use of ALD to tune the properties of 3D printed parts.

show abstract

Section: Illustration Of the Combination Of 3d Printing And Atomic La...mentioning

confidence: 99%

Nanometric 3D Printing of Functional Materials by Atomic Layer Deposition

Muñoz‐Rojas¹,

Weber²,

Vallée³

et al. 2022

Advanced Additive Manufacturing

Self Cite

View full text Add to dashboard Cite

show abstract

“…Now a days 3D printing was also used for air filtration to remove toxic gases, biological aerosol particles which include viruses, bacteria cells, and so on 163 . Personal protective masks can act as a barrier against some pollutants; however, conventional procedures make it difficult to produce a highly effective barrier.…”

Section: Applicationsmentioning

confidence: 99%

A short review on fused deposition modeling 3D printing of bio‐based polymer nanocomposites

Mandala

Bannoth

Akella³

et al. 2021

J of Applied Polymer Sci

View full text Add to dashboard Cite

Fused deposition modeling (FDM), one among the most commonly used additive manufacturing (AM), techniques has been widely used in recent years to produce customized parts with intricate geometries, especially from thermoplastics. This method was limited in its ability to produce parts for industrial applications due to inferior properties and the poor quality of fabricated parts. Hence, researchers are being driven to discover novel materials that are viable for FDM in order to keep up with enormous demand for functional products. In the recent years, it is widely recognized that the emphasis was placed on the bio‐based polymer composite matrices rather than conventional thermoplastics due to its vital advantages that aid in the replacement of synthetic and perilous materials. On this context, this review focuses on the recent advancements in FDM printing with biomaterials. Specifically, attempts have been made to investigate and provide nutshell of 3D printing of current bio‐based nanocomposites which consist of either bio‐derived filler or polymer matrices in order to make 3D printing sustainable. The effect of fillers on the filaments and FDM based products, evolution of novel characteristics of bio nanocomposites, the printability of the developed composites and their development in leading applications were also investigated and summarized.

show abstract

“…3D-printed polymers have several industrial oil and gas use cases. Pellejero et al [ 52 ] reported the use of functionalized 3D-printed ABS filters for the capture of toxic gas. Chang et al [ 53 ] 3D-printed a porous polyimide for oil impregnation.…”

Section: Overview Of Am Techniquesmentioning

confidence: 99%

Additively manufactured high-performance polymeric materials and their potential use in the oil and gas industry

et al. 2021

View full text Add to dashboard Cite

Graphical abstract The oil and gas industry has been tagged as among the largest revenue-generating sectors in the world. High-performance polymers (HPPs), on the other hand, are among the most useful industrial materials, while the utility of 3D printing technologies has evolved and transitioned from rapid prototyping of composite materials to manufacturing of functional parts. In this prospective, we highlight the potential uses and industrial applications of 3D-printed HPP materials in the oil and gas sector, including the challenges and opportunities present.

show abstract

Functionalization of 3D printed ABS filters with MOF for toxic gas removal

Cited by 31 publications

References 55 publications

Nanometric 3D Printing of Functional Materials by Atomic Layer Deposition

Nanometric 3D Printing of Functional Materials by Atomic Layer Deposition

A short review on fused deposition modeling 3D printing of bio‐based polymer nanocomposites

Additively manufactured high-performance polymeric materials and their potential use in the oil and gas industry

Contact Info

Product

Resources

About