Fundamentals of Fibre Reinforced Composite Materials

Bunsell, Anthony R.; Renard, J.

doi:10.1201/9781420056969

Cited by 152 publications

(128 citation statements)

References 0 publications

Supporting

Mentioning

111

Contrasting

Unclassified

Order By: Relevance

“…A FRC is a typical composite material made of a plastic matrix that is reinforced by fine thin fibers, which have high tensile strength and a high flexural modulus. It is also called in the literature fiber-reinforced polymer (FRP) or glass-reinforced plastic (GRP) [2].…”

Section: Fiber Reinforced Compositementioning

confidence: 99%

E-Glass Fiber Reinforced Composites in Dental Applications

Zhang

Matinlinna

2011

Silicon

155

View full text Add to dashboard Cite

Fiber reinforced composites (FRCs) are more and more widely applied in dentistry to substitute for metallic restorations: periodontal splints, fixed partial dentures, endodontic posts, orthodontic appliances, and some other indirect restorations. In general in FRCs, the fiber reinforcement provides the composite structure with better biomechanical performance due to their superior properties in tension and flexure. Nowadays, the E-glass fiber is most frequently used because of its chemical resistance and relatively low cost. Growing interest is being paid to enhance its clinical performance. Moreover, various techniques are utilized to reinforce the adhesion between the fiber and the matrix. Oral conditions set special requirements and challenges for the clinical applications of FRCs. The biomechanical properties of dental materials are of high importance in dentistry, and given this, there is on-going scientific interest to develop E-glass fiber reinforced composite systems. FRCs are generally biocompatible and their toxicity is not a concern.

show abstract

Section: Fiber Reinforced Compositementioning

confidence: 99%

E-Glass Fiber Reinforced Composites in Dental Applications

Zhang

Matinlinna

2011

Silicon

155

View full text Add to dashboard Cite

show abstract

“…В настоящее время в аэрокосмической и оборонной промышленности широкое распро-странение получили полимерные композиционные материалы (ПКМ), состоящие из армиру-ющих волокон (угле-и стеклоткань) и эпоксидных смол [1]. Это обусловлено тем, что ПКМ обладают такими свойствами, как коррозийная стойкость, высокая прочность и легкость, ста-бильность размеров, минимальное поглощение влаги и возможность изготовления изделий сложной формы.…”

Section: Introductionunclassified

Quality Control Parametrs of Manufacturing Composite Antenna Reflector

Kupriyanova¹,

Serzhantova²,

Banschikova³

2015

J. Sib. Fed. Univ. Eng. technol.

View full text Add to dashboard Cite

“…The Weibull modulus for the majority of samples was in the range of 3.4 to 8.4, with the exception of CNT-g-CF (300 V), which had a higher Weibull modulus in the range of around 11, indicating a lower variance in strength between samples which is shown in the fit of the tensile data ( Figure 5 (a)). A Weibull modulus of around 5 is common for carbon fibers, [58] but the value can be as high as 14 for as-received carbon fibers, whilst Weibull moduli in the range of 5 to 7 have been reported for CNT-g-CF samples. [59][60][61] Single fiber fragmentation measurements identify high fiber strengths due to the short effective gauge.…”

Section: Tensile Properties Of (Cnt-grafted-)fibersmentioning

confidence: 99%

Continuous carbon nanotube synthesis on charged carbon fibers

Anthony

Sui

Kellersztein

et al. 2018

Composites Part A: Applied Science and Manufacturing

View full text Add to dashboard Cite

Carbon nanotube grafted carbon fibers (CNT-g-CFs) were prepared continuously, spool to spool, via thermal CVD. The application of an in-situ potential difference (300 V), between the fibers and a cylindrical graphite foil counter electrode, enhanced the growth, producing a uniform coverage of carbon nanotubes with diameter ca. 10 nm and length ca. 125 nm. Single fiber tensile tests show that this approach avoids the significant reduction of the underlying carbon fiber strengths, which is usually associated with CVD grafting processes. Single fiber fragmentation tests in epoxy, with in-situ video fragment detection, demonstrated that the CNT-g-CFs have the highest interfacial shear strength reported for such systems (101 ± 5 MPa), comparable to state-of-the-art sizing controls (103 ± 8 MPa).Single fiber pull-out data show similar trends. The short length of the grafted CNTs is particularly attractive for retaining the volume fraction of the primary fibers in composite applications.

show abstract

Fundamentals of Fibre Reinforced Composite Materials

Cited by 152 publications

References 0 publications

E-Glass Fiber Reinforced Composites in Dental Applications

E-Glass Fiber Reinforced Composites in Dental Applications

Quality Control Parametrs of Manufacturing Composite Antenna Reflector

Continuous carbon nanotube synthesis on charged carbon fibers

Contact Info

Product

Resources

About