Health Monitoring of Structural Materials and Components

Adams, Douglas E.

doi:10.1002/9780470511589

Cited by 196 publications

(152 citation statements)

References 0 publications

Supporting

Mentioning

148

Contrasting

Unclassified

Order By: Relevance

“…An extensive description of the principles, advantages, and limitations of each of the above technologies is beyond the scope of this paper. Interested readers may refer to some of the books in the area of NDE and SHM [15][16][17][18][19]. The performance and the feasibility of each technology are associated with their capability to gauge limited or large sections at once, and the need to interrupt service to allow for direct access.…”

Section: Pipe Inspectionmentioning

confidence: 99%

Water and Wastewater Pipe Nondestructive Evaluation and Health Monitoring: A Review

Rizzo

2010

Advances in Civil Engineering

View full text Add to dashboard Cite

pipe networks assure the transportation of primary commodities such as water, oil, and natural gas. The quantitative and early detection of defects in pipes is critical in order to avoid severe consequences. As a result of high-profile accidents and economic downturn, research and development in the area of pipeline inspection has focused mainly on gas and oil pipelines. Due to the low cost of water, the development of nondestructive inspection (NDI) and structural health monitoring (SHM) technologies for fresh water mains and sewers has received the least attention. Moreover, the technical challenges associated with the practical deployment of monitoring system demand synergistic interaction across several disciplines, which may limit the transition from laboratory to real structures. This paper presents an overview of the most used NDI/SHM technologies for freshwater pipes and sewers. The challenges that said infrastructures pose with respect to oil and natural gas pipeline networks will be discussed. Finally, the methodologies that can be translated into SHM approaches are highlighted.

show abstract

Section: Pipe Inspectionmentioning

confidence: 99%

Water and Wastewater Pipe Nondestructive Evaluation and Health Monitoring: A Review

Rizzo

2010

Advances in Civil Engineering

View full text Add to dashboard Cite

show abstract

“…Classes, symbols, and risk levels for steel gas pipelines. The database of reference signals was created by conducting a series of tests on various types of reinforced concrete beams and specimens under various loads, including cyclic loading for the modeling of the car's passage [18][19][20][21][22][23][24]. The tests aimed at finding predominant destructive processes that might occur during testing of reinforced concrete structures under operation.…”

Section: Acoustic Emission Evaluation Of Gas Pipelinesmentioning

confidence: 99%

Acoustic Emission Method for Locating and Identifying Active Destructive Processes in Operating Facilities

Świt

2018

Applied Sciences

View full text Add to dashboard Cite

Featured Application: The data collected can be the basis for determining the structural condition of the structure.Abstract: Durability, safety, and usability are the three foundations of structural reliability, vital in the economic and social context. As the locating and tracking of potential damage and evaluating its impact on the condition of the structure are part of service life assessment, relevant methods should be developed that would detect the onset of the deterioration process and enable the monitoring of its progress within the entire volume of the structure, not only in the areas selected in a subjective way. The acoustic emission (AE) method relying on the analysis of active destructive processes can be the best choice. This article reports the results of the application of the AE method for identifying active destructive processes and tracking their development during the routine operation of various types of structures.

show abstract

“…The computational simulation can improve the effectiveness of the analysis and solve the key problems of structural health monitoring and dynamic system identification [15] - [18], coupling technique [19] and [20], structural integrity [21] and [22], nonlinear dynamics [23], especially, of nonlinear aero elasticity [24]. In the practice of designing and production of new rotorcraft, the fullscale test of the basic prototype is needed before the first flight.…”

Section: Introductionmentioning

confidence: 99%

On the Dynamic Response Prediction at the Full-Scale Test of Aircraft Component

Pavelko

Nevskij²

2017

Transport and Aerospace Engineering

View full text Add to dashboard Cite

-Several general effects of boundary conditions and their adequate description at structural dynamic computational simulation constitute the main subject of the discussion. First, an analytical model of elastically supported beam was considered to evaluate the effects of support compliance to the basic dynamic characteristics. Second, a more complex model of a body with elastic support was simulated. Some general properties of structure dynamics were analysed.

show abstract

Health Monitoring of Structural Materials and Components

Cited by 196 publications

References 0 publications

Water and Wastewater Pipe Nondestructive Evaluation and Health Monitoring: A Review

Water and Wastewater Pipe Nondestructive Evaluation and Health Monitoring: A Review

Acoustic Emission Method for Locating and Identifying Active Destructive Processes in Operating Facilities

On the Dynamic Response Prediction at the Full-Scale Test of Aircraft Component

Contact Info

Product

Resources

About