High-frequency EMC design verification through full-wave simulations and measurements in Reverberation Chamber

Zhou, Xiaoxia; Li, Jing; Fan, Hongmei; Bhobe, Alpesh; Sochoux, Philippe; Yu, Jinghan

doi:10.1109/isemc.2013.6670427

Cited by 11 publications

(3 citation statements)

References 4 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…A mode-stirred dual RC was used to evaluate the TRP from the optical cage connector [17]- [24], and only the connector was in the receiving side of the chamber as shown in Fig. 3(b).…”

Section: B Simulation Model Validation (Trp)mentioning

confidence: 99%

EMI Coupling Paths and Mitigation in a Board-to-Board Connector

Xiao

Toor

et al. 2015

IEEE Trans. Electromagn. Compat.

Self Cite

View full text Add to dashboard Cite

Cage connectors for optical subassembly I/O modules have been identified as one of the main coupling paths in an optical link at the front-end of switches and routers. In the study presented herein, the simulation model used to study electromagnetic interference coupling physics and mitigation of the optical cage connector was corroborated by comparing the measured and simulated results for the total radiated power (TRP). Currents on the adjacent ground references to the differential signal conductors caused half-wave resonant peaks in the TRP response in the frequency range of 4-18 GHz. At frequencies from 18 to 28 GHz, both full-wave simulation and analytical formulas indicate that the radiation results primarily from the currents on the signal traces. The radiation from the optical cage connector was suppressed with absorbing materials, and the coupling path was verified, together with the optical cage and module enclosure.Index Terms-Absorbing material, electromagnetic interference (EMI) coupling path, high frequency, mitigation, optical cage connector, radiation mechanism, total radiated power (TRP).

show abstract

“…A mode-stirred dual RC was used to evaluate the TRP from the optical cage connector [17]- [24], and only the connector was in the receiving side of the chamber as shown in Fig. 3(b).…”

Section: B Simulation Model Validation (Trp)mentioning

confidence: 99%

EMI Coupling Paths and Mitigation in a Board-to-Board Connector

Xiao

Toor

et al. 2015

IEEE Trans. Electromagn. Compat.

Self Cite

View full text Add to dashboard Cite

show abstract

“…To reduce the heating of the devices inside, the use of heat sinks is proposed, for power semiconductors. These elements have the quality of absorbing the heat and in this way lead it to the outside, avoiding the possible damage of the circuit as of the elements that compose it [3][4][5].…”

Section: Introductionmentioning

confidence: 99%

Design of passive heat sinks to power semiconductor with the cesaro curve

Ruiz-Cardenas

Llano-Sánchez

Cajeli

et al. 2020

redin

View full text Add to dashboard Cite

In the design of electronic circuits, stands out the power stage, which is responsible of increasing the signal characteristics, as current and voltage, for an appropriate performance of the device to fabricate. However, this stage is composed of elements like transistors, which may have a low performance, due to the undesired temperature increase, as a result of reaching the desired power. To mitigate the loss of power and with it, the temperature rise, the management of heat sink is proposed, in order to keep the work of the power stage at a stable level and avoid thermal fractures within the circuit. This manuscript presents the obtained results of the thermal analysis in finite elements of the heat sink with fins in the form of a Cesaro curve, for power semiconductors, which evidence the increase in the heat flow, with respect to the commercial ones and so, facilitate the heat evacuation for conditioning the voltage and/or current.

show abstract

“…Dielectric conductivity and permittivity tests in the 30 GHz to 40 GHz range performed in a cylindrical RC were given in [22]. Emission tests of different electrical components from 1 GHz to 40 GHz have been performed in [23]. In [24], the design and experimental R 0018-926X (c) 2015 IEEE.…”

mentioning

confidence: 99%

Estimating and Reducing Uncertainty in Reverberation-Chamber Characterization at Millimeter-Wave Frequencies

Senić

Remley

Wang

et al. 2016

IEEE Trans. Antennas Propagat.

View full text Add to dashboard Cite

This contribution provides techniques for accurately characterizing uncertainty when measuring total radiated power at millimeter-wave frequencies. The setup is based on the reverberation chamber as a well-known measurement environment capable of performing total radiated power measurements of wireless devices. We show that by applying various stirring techniques, we can reduce the random component of measurement uncertainty to around 2%. We use a model for estimating the uncertainty for total radiated power measurements based on the K factor which is compared to uncertainties calculated from relative power measurements and we show excellent agreement. We perform a significance test to confirm that the uncertainty due to the limited number of mode-stirred samples dominates over the uncertainty due to the lack of spatial uniformity. The observed uncertainty is also compared to an ideal chamber situation and shows good agreement.Index Terms-Measurement uncertainty, millimeter wave, reverberation chamber, total radiated power, wireless systems.

show abstract

High-frequency EMC design verification through full-wave simulations and measurements in Reverberation Chamber

Cited by 11 publications

References 4 publications

EMI Coupling Paths and Mitigation in a Board-to-Board Connector

EMI Coupling Paths and Mitigation in a Board-to-Board Connector

Design of passive heat sinks to power semiconductor with the cesaro curve

Estimating and Reducing Uncertainty in Reverberation-Chamber Characterization at Millimeter-Wave Frequencies

Contact Info

Product

Resources

About