High temperature potential of flip chip assemblies for automotive applications

Abstract

Flip Chip technology has been widely accepted within microelectronics as a technology for maximum miniaturization. Typical applications today are mobile products as cellular phones or GPS devices. The upper temperature limits for such applications range from 80 °C to a maximum of 125 °C. To widen the application range of Flip Chip technology and to address the volume market of automotive and industrial electronics the development of high temperature capable assemblies is crucial. Typical scenario for the integration of electronics into a car is a control unit in the engine compartment, where ambient temperatures are around 150 °C, package junction temperatures may range from 175 °C to 200 °C and peak temperature may exceed these values.When using Flip Chip technology under high temperature conditions major challenges are found in the application of interconnect media and supporting polymers. At elevated temperatures the intermetallic phase formation of lead-free solders might lead to a reliability decrease, where polymeric materials as substrate and encapsulant do potentially show mismatched thermo-mechanical properties or material degradation and thus reliability is reduced. Literature does typically describe Flip Chip technologies behavior on organic substrates for consumer applications, but almost no information is available on the performance at temperatures beyond 125 °C. Within the European project HOTCAR, dealing with high temperature electronics for automotive use in general, a German consortium consisting of an IC manufacturer (IFX), two technology users (Siemens VDO & Temic) and a research institute (Fraunhofer IZM) have cooperated to evaluate the high temperature potential of lead-free Flip Chip technology for automotive applications.According to automotive demands an experimental study on the suitability of advanced Underfill encapsulants for high temperature has been performed. With the outcome of this pre-study two promising underfill materials were selected and used in a test run with an automotive test vehicle. This comprises an automotive grade µController mounted on a substrate manufactured according to automotive standards, as the major system components. Solder material used was SnAg with a Ni UBM in combination with two different substrate finishes NiAu and immersion Sn. These test devices were submitted to temperature cycles according to automotive specifications with a maximum temperature of 150 °C. Intermetallic phase formation was studied after high temperature storage by cross sections and shear tests. Typical failure modes for Flip Chip failure have been identified and are described in detail.The experimental reliability investigations were backed by thermo-mechanical simulations. Taking advantage of the so-called submodelling technique, the solder joint behavior could be studied in detail for lead-free solders. Starting stress-free at 150 °C, the calculations followed the real thermal cycling regime. As primary results, the accumulated equivalent creep strain and creep strain energy di...

Duromer MID technology for system-in-package generation

“…Typical CTEs below glass transition temperature range from 8 to 14 10 K, Young's moduli range from 4 to 8 GPa. values are higher than 160 C. Regarding the long term behavior of these materials, investigations performed at IZM also prove the high thermal stability and media resistance of duromer materials [3], allowing them to be used as a base material also for demanding automotive applications. Fig.…”

Enhancement of barrier properties of encapsulants for harsh environment applications

“…The reason for this behavior is the nonlinear dependence of penetration time on concentration of zeolite. Additionally, the thermomechanical and adhesion properties of the encapsulant in the vicinity of the chip play an important role for the reliability [1][2][3]. For this reason, single-and multilayer encapsulation experiments have been designed, in which two types of fillers are distributed differently.…”

“…On the one hand, typically true for encapsulants, mechanical stresses are imposed on interconnects and on the other hand humidity can easily access the interface and can cause corrosion. Both effects have a negative influence on the reliability of the assembly [1,2]. Water in polymers can also lead to a softening and/or to a swelling of the material resulting in degraded thermo-mechanical properties and higher stresses in a package [3].…”

Power Modulation Investigation for High Temperature (175-200 degrees Celcius) Automotive Application

“…However, none have been proposed for 175°C. [66] A new polymer-based film, PIBO, has been proposed to address these issues. PIBO is a high temperature stable polyimide film with resistance to plasma degradation.…”