Injection mechanisms in a III -nitride light-emitting diode as seen by self-emissive electron microscopy

The large polarization barriers between the quantum wells and quantum barriers in long-wavelength GaN-based light-emitting diodes (LEDs) inhibit their performance by requiring excess driving voltages to reach standard operating current densities. Lateral injection of carriers directly into quantum wells is required to circumvent this issue. V-defects are naturally occurring inverted hexagonal defects with semipolar 101¯1-plane sidewalls generated on surface depressions from threading dislocations. LEDs engineered to intentionally generate V-defects below the active region of the LED can achieve lateral carrier injection through the V-defect sidewalls and have already been able to demonstrate world record wall-plug efficiencies for LEDs in the green-red wavelengths. V-defects can be enlarged during kinetically limited growth where the growth rate of the c-plane GaN is faster than that of their sidewalls, leaving them unfilled. We report on the metal organic chemical vapor deposition growth conditions required to fill in V-defects with p-GaN during epitaxial growth of the LED post the active region. Circular transmission length measurements of Pd/Au contacts processed on p-GaN surfaces with various amounts of unfilled V-defects showed no significant difference in their sheet resistance and specific contact resistance. J–V measurements of LEDs grown with varying unfilled V-defect densities showed no significant difference in the forward bias regime. However, in the reverse bias regime, catastrophic breakdown occurred at markedly lower voltages for samples with larger unfilled V-defect densities. This suggests that unfilled V-defects may act as hotspots for device failure, and planarizing LED surfaces may help prevent early degradation of LED devices.

Planarization of p-GaN surfaces on MOCVD grown V-defect engineered GaN-based LEDs

Tak,

Quevedo,

et al. 2024

Dynamics of carrier injection through V-defects in long wavelength GaN LEDs

Marcinkevičius,

Tak,

Chow

et al. 2024

The efficiency of high-power operation of multiple quantum well (QW) light emitting diodes (LEDs) to a large degree depends on the realization of uniform hole distribution between the QWs. In long wavelength InGaN/GaN QW LEDs, the thermionic interwell hole transport is hindered by high GaN barriers. However, in polar LED structures, these barriers may be circumvented by the lateral hole injection via semipolar 101¯1 QWs that form on the facets of V-defects. The efficiency of such carrier transfer depends on the transport time since transport in the semipolar QWs is competed by recombination. In this work, we study the carrier transfer from the semipolar to polar QWs by time-resolved photoluminescence in long wavelength (green to red) LEDs. We find that the carrier transfer through the semipolar QWs is fast, a few tens of picoseconds with the estimated room temperature ambipolar diffusion coefficient of ∼5.5 cm2/s. With diffusion much faster than recombination, the hole transport from the p-side of the structure to the polar QWs should proceed without a substantial loss, contributing to the high efficiency of long wavelength GaN LEDs.

Carrier diffusion in long wavelength InGaN quantum well LEDs after injection through V-defects

Yapparov,

Tak,

Ewing

et al. 2024

The efficiency of operation of GaN-based light emitting diodes (LEDs) to a large degree relies on realization of a uniform hole distribution between multiple quantum wells (QWs) of the active region. Since the direct thermionic transport between the QWs is inefficient, the hole injection through semipolar 101¯1 QWs that form on the facets of V-defects has been suggested as an alternative approach. However, for an efficient LED operation, the carrier distribution should be uniform not only vertically, between the QWs but also laterally, within individual QWs. In this work, the lateral carrier distribution in long wavelength InGaN/GaN QW LEDs is studied by the scanning near-field optical microscopy. The measurements have shown that emission is concentrated around the V-defect injectors. At high currents, the diffusion length of holes in polar QWs was found to be ∼0.6–1 μm and the hole diffusion coefficient ∼0.6 cm2/s. The obtained data should aid design of the V-defect injectors for a laterally uniform carrier distribution in the active region QWs.