Investigation of electrocoagulation reactor design parameters effect on the removal of cadmium from synthetic and phosphate industrial wastewater

Brahmi, Khaled; Bouguerra, Wided; Hamrouni, Béchir; Elaloui, Elimame; Loungou, Mouna; Tlili, Zied

doi:10.1016/j.arabjc.2014.12.012

Cited by 154 publications

(53 citation statements)

References 27 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…According to [68], they mentioned that the total cost estimation typically includes the chemical reagents, cost of electricity, sludge handlings, operators, and maintenance and equipment used in the EC system. However, in laboratory research, the electrode, consumption of electrical energy, and chemicals are the main parameters of the operating expenditure [69,70]. Also, the consumption of zeolite is also revealed in this analysis using Equation (4) as follows:…”

Section: The Economic Aspect Of the Zaep Treatmentmentioning

confidence: 94%

Optimization and Analysis of Zeolite Augmented Electrocoagulation Process in the Reduction of High-Strength Ammonia in Saline Landfill Leachate

Hamid

Aziz

Yusoff

et al. 2020

Water

View full text Add to dashboard Cite

This work examined the behavior of a novel zeolite augmented on the electrocoagulation process (ZAEP) using an aluminum electrode in the removal of high-strength concentration ammonia (3471 mg/L) from landfill leachate which was saline (15.36 ppt) in nature. For this, a response surfaces methodology (RSM) through central composite designs (CCD) was used to optimize the capability of the treatment process. Design-Expert software (version 11.0.3) was used to evaluate the influences of significant variables such as zeolite dosage (100–120 g), current density (540–660 A/m2), electrolysis duration (55–65 min), and initial pH (8–10) as well as the percentage removal of ammonia. It is noted that the maximum reduction of ammonia was up to 71%, which estimated the optimum working conditions for the treatment process as follows: zeolite dosage of 105 g/L, the current density of 600 A/m2, electrolysis duration of 60 min, and pH 8.20. Furthermore, the regression model indicated a strong relationship between the predicted values and the actual experimental results with a high R2 of 0.9871. These results provide evidence of the ability of the ZAEP treatment as a viable alternative in removing high-strength landfill leachate of adequate salinity without the use of any supporting electrolyte.

show abstract

Section: The Economic Aspect Of the Zaep Treatmentmentioning

confidence: 94%

Optimization and Analysis of Zeolite Augmented Electrocoagulation Process in the Reduction of High-Strength Ammonia in Saline Landfill Leachate

Hamid

Aziz

Yusoff

et al. 2020

Water

View full text Add to dashboard Cite

show abstract

“…As an important parameter, the combination of electrodes employed as well as the EC reactor influence significantly the removal efficiency achieved in some cases, such as arsenate, arsenite, cadmium, manganes and silver [28,44,51,63,72,73,76,82,98,104,106,185,[199][200][201][202][203][204][205][206][207][208][209][210][211][212][213][214][215][216][217][218] Arsenite(III) was quase completely removed when Al and Fe electrodes were used for treating synthetic effluents [63,75,106,[199][200][201][202]. The most used EC reactor for arsenite(III) elimination was MP-P by using soft electrolytic conditions (j or E).…”

Section: Heavy Metalsmentioning

confidence: 99%

Electrocoagulation and advanced electrocoagulation processes: A general review about the fundamentals, emerging applications and its association with other technologies

Garcia‐Segura

Eiband

Melo

et al. 2017

Journal of Electroanalytical Chemistry

573

213

View full text Add to dashboard Cite

The electrocoagulation (EC) process is an electrochemical means of introducing coagulants and removing suspended solids, colloidal material, and metals, as well as other dissolved solids from water and wastewaters. EC process has been successfully employed in removing pollutants, pesticides, and radionuclides. This process also removes harmful microorganisms. More often during EC operation, direct current is applied and electrode plates are sacrificed (dissolved into solution). The electrodissolution causes an increased metal concentration in the solution that finally precipitates as oxides and hydroxides. Due to the process design and low cost material, the EC process is widely accepted over other physicochemical processes. In this frame, this paper presents a general review of efficient EC technologies developed to remove organic and inorganic matter from wastewaters for environmental protection. Fundamentals and main applications of EC as well as progress of emerging EC treatments are reported. The influence of iron or aluminum anode on depollution of synthetic or real effluents is explained. The advantages of EC mechanisms with Al and Fe electrodes are extensively discussed. There are presented the advanced EC processes with in situ generation of hydroxyl radical. The importance of the operating parameters for efficient application of the EC process as well as the combination of this electrochemical technology with electroanalysis techniques and other technologies are commented.

show abstract

“…This is ascribed to the fact that at higher electrical current, more oxidation occurs within the anodes followed by higher coagulation and flocculation. Moreover, increasing electrical current brings about greater bubble density having smaller size, which effectively promotes pollutant removal by electroflotation [35] [36]. It was observed that the process significantly shown the effect of electrical current in 20 min reaction time as the color of the wastewater undergoes individual decreases by increasing the electrical current.…”

Section: Effect Of Electrical Currentmentioning

confidence: 99%

Removal of Reactive Dye from Textile Mill Wastewater by Leading Electro-Coagulation Process Using Aluminum as a Sacrificial Anode

Sadik¹

2019

ACES

View full text Add to dashboard Cite

This work presents the highest color removal efficiency for Textile wastewater by Electrocoagulation (EC) process using Aluminum as a sacrificial anode which is presently used for the purification of many types of water and wastewater. The effecting parameters such as applied electrical current, electrolysis time and initial pH were studied to achieve higher removals. In this process, sample was taken from real effluent of reactive dyes fabric. The performance of Electrocoagulation process was carried out in batch reactor at regular interval of 20 minutes. Obtained results indicated the most effective color removal efficiency was achieved at 0.75A of applied electrical Current. They were (97.5%-98.1%), at electrolysis time of 120 minutes, pH10, pH7 respectively and COD removal efficiency was (54 %-65%) at 0.75A, 0.9A respectively. In this work, the initial pH did not strongly affect the removal efficiencies significantly over a wide range. Therefore, adjustment of initial pH before treatment was not required in this practical application. The power consumption was found to be 6 kWh/m 3. To determine COD removal rate dependency to electrical current, a kinetic study was carried out and data were in good covenant with the first order kinetic model.

show abstract

Investigation of electrocoagulation reactor design parameters effect on the removal of cadmium from synthetic and phosphate industrial wastewater

Cited by 154 publications

References 27 publications

Optimization and Analysis of Zeolite Augmented Electrocoagulation Process in the Reduction of High-Strength Ammonia in Saline Landfill Leachate

Optimization and Analysis of Zeolite Augmented Electrocoagulation Process in the Reduction of High-Strength Ammonia in Saline Landfill Leachate

Electrocoagulation and advanced electrocoagulation processes: A general review about the fundamentals, emerging applications and its association with other technologies

Removal of Reactive Dye from Textile Mill Wastewater by Leading Electro-Coagulation Process Using Aluminum as a Sacrificial Anode

Contact Info

Product

Resources

About