Investigation of structure–mechanical properties relations of dual-axially forged Ti-based low-alloys

Zadorozhnyy, V.Yu.; Щетинин, И. В.; Железный, М. В.; Chirikov, N.V.; Wada, Takeshi; Kato, Hidemi; Louzguine-Luzgin, Dmitri V.

doi:10.1016/j.msea.2015.02.065

Cited by 12 publications

(4 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Our group was successful in developing a low-alloyed Ti-based (Ti 94 Fe 3 Cu 3 ) alloy with comparatively good mechanical and electrochemical properties by simple thermo-mechanical treatment following a dual-axial forging procedure. These findings gave way to enhancing the mechanical properties to a further extent [31][32][33][34]. Interchanging Fe and Cu with Pd and Ag enhanced the biocompatibility, with a slight effect on the mechanical properties [35][36][37].…”

Section: Introductionmentioning

confidence: 94%

“…Dual-axial forging was carried out based on our previous studies [24,[31][32][33][34][35][36][37][38] and Ti-Fe-Cu-Sn phase diagrams. In brief, the initial forging procedure was carried out along the long axis with 15 cycles of ingot rotation at a constant temperature of 900 • C, which corresponds to β-Ti region.…”

Section: Dual-axial Forging Procedures and Mechanical Testingmentioning

confidence: 99%

“…Keeping all this in mind, all our previous research was focused on developing low-alloyed α + β titanium alloys [31][32][33][34][35][36][37][38]. Our group was successful in developing a low-alloyed Ti-based (Ti 94 Fe 3 Cu 3 ) alloy with comparatively good mechanical and electrochemical properties by simple thermo-mechanical treatment following a dual-axial forging procedure.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Novel α + β Type Ti-Fe-Cu Alloys Containing Sn with Pertinent Mechanical Properties

Zadorozhnyy

Ketov

Wada

et al. 2019

Metals

View full text Add to dashboard Cite

Rising demand for bone implants has led to the focus on future alternatives of alloys with better biocompatibility and mechanical strength. Thus, this research is dedicated to the synthesis and investigation of new compositions for low-alloyed Ti-based compounds, which conjoin relatively acceptable mechanical properties and low elastic moduli. In this regard, the structural and mechanical properties of α + β Ti-Fe-Cu-Sn alloys are described in the present paper. The alloys were fabricated by arc-melting and tilt-casting techniques which followed subsequent thermo-mechanical treatment aided by dual-axial forging and rolling procedures. The effect of the concentrations of the alloying elements, and other parameters, such as regimes of rolling and dual-axial forging operation, on the microstructure and mechanical properties were thoroughly investigated. The Ti94Fe1Cu1Sn4 alloy with the most promising mechanical properties was subjected to thermo-mechanical treatment. After a single rolling procedure at 750 °C, the alloy exhibited tensile strength and tensile plasticity of 1300 MPa and 6%, respectively, with an elastic modulus of 70 GPa. Such good tensile mechanical properties are explained by the optimal volume fraction balance between α and β phases and the texture alignment obtained, providing superior alternatives in comparison to pure α- titanium alloys.

show abstract

Section: Introductionmentioning

confidence: 94%

Section: Dual-axial Forging Procedures and Mechanical Testingmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Novel α + β Type Ti-Fe-Cu Alloys Containing Sn with Pertinent Mechanical Properties

Zadorozhnyy

Ketov

Wada

et al. 2019

Metals

View full text Add to dashboard Cite

show abstract

“…Однако существенный недостаток этих сплавов -значительное количество легирующих элементов, входящих в состав, в том числе дорогостоящих: до 6,9 Al, 4,5 V и 5,0 Mo. Ранее авторами [13][14][15][16][17] было показано, что совместное легирование железом и медью положительно влияет на структуру кованых титановых сплавов. Однако в связи с недостаточной технологичностью таких сплавов для ускорения разработки промышленных методов обработки давлением требуется изучение деформационного поведения и эволюции микроструктуры в широком диапазоне скоростей и температур деформации, а также построение реологической модели связи напряжения течения с параметрами пластической деформации.…”

Section: Introductionunclassified

Study Into Structural Evolution of Two-Phase Titanium Alloy During Thermal Deformation Processing

Чурюмов

Спасенко

Khazhina

et al. 2018

Izv.VUZ. Tsvet. Met.

View full text Add to dashboard Cite

This paper studies Ti–3,5Fe–4Cu–0,2B two-phase titanium alloy behavior during its thermal deformation processing under uniaxial compression. Boron was added to obtain a fine-grained structure in the cast state. Samples of alloys 6 mm in diameter were obtained by melting pure components in a vacuum induction furnace with their subsequent crystallization into a solid copper mold. Uniaxial compression tests with a true strain of 0,9 were performed using the Gleeble 3800 thermal-mechanical physical simulation system at 750, 800 and 900 °C and strain rates of 0,1; 1 and 10 s–1. Scanning electron microscopy was used to study the microstructure of the alloy in its initial and deformed states. A model of flow stress dependence on temperature and strain rate was built as a result of the tests. It is shown that pressure treatment involves recrystallization of the initial cast structure containing solid solutions based on α-Ti, β-Ti and titanium diboride aggregates. During the deformation process, the volume fraction of α-titanium solid solution grains decreases with rising temperature, and the fraction of the β phase, on the contrary, increases. In this case, the average grain size of solid solutions based on α-Ti and β-Ti varies insignificantly after deformation in almost all of the studied modes. It is shown that the preferred mode of hot pressure treatment for obtaining a high complex of mechanical properties in the investigated alloy is a temperature range of 750– 800 °C, since α-phase grain sizes increase from 2,2 to 4,5 μm with an increase in temperature to 900 °C.

show abstract

Microstructure and Mechanical Properties of a High-Strength Ti-4Al-2Fe-3Cu Alloy Fabricated by Sintering and Hot Extrusion

Najafizadeh

Zhang

Maldar

et al. 2022

Metall Mater Trans A

View full text Add to dashboard Cite

Investigation of structure–mechanical properties relations of dual-axially forged Ti-based low-alloys

Cited by 12 publications

References 22 publications

Novel α + β Type Ti-Fe-Cu Alloys Containing Sn with Pertinent Mechanical Properties

Novel α + β Type Ti-Fe-Cu Alloys Containing Sn with Pertinent Mechanical Properties

Study Into Structural Evolution of Two-Phase Titanium Alloy During Thermal Deformation Processing

Microstructure and Mechanical Properties of a High-Strength Ti-4Al-2Fe-3Cu Alloy Fabricated by Sintering and Hot Extrusion

Contact Info

Product

Resources

About