Joining of dissimilar materials with friction stir welding

Okamura, Hisanori; Aota, Kinya

doi:10.1533/wint.2004.3344

Cited by 55 publications

(42 citation statements)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Jiangwei et al (2002) report the possibility of diffusion bonding of these alloys, Fuji et al (1997) succeed in friction welding, Okamura and Aota (2004) report quality joining by friction stir welding, Ege and Inal (2000) performed explosive welding. Takemoto and Okamoto (1988) report the possibility of joining by brazing.…”

Section: Introductionmentioning

confidence: 99%

Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V

Tomashchuk

Sallamand

Cicala

et al. 2015

Journal of Materials Processing Technology

115

View full text Add to dashboard Cite

is an open access repository that collects the work of Arts et Métiers ParisTech researchers and makes it freely available over the web where possible. a b s t r a c tThe tensile strength of direct AA5754/Ti6Al4V joints performed by high speed Yb:YAG laser welding is found to be determined by morphology and phase content of dissimilar interface formed between contacting Al-rich and Ti-rich melted zones. Three types of contact interfaces were observed: (1) Maximal linear tensile force (220 N/mm for 2 mm thick weld) can be attained when thin contact interface is formed. In this case, the fracture starts in intermetallics-rich zone but propagates mainly in Al-rich melted zone, when in other cases it occurs in brittle intermetallic layers.

show abstract

Section: Introductionmentioning

confidence: 99%

Direct keyhole laser welding of aluminum alloy AA5754 to titanium alloy Ti6Al4V

Tomashchuk

Sallamand

Cicala

et al. 2015

Journal of Materials Processing Technology

115

View full text Add to dashboard Cite

show abstract

“…The material softens due to frictional heat without attaining the dissolving point and permits traversing of tool besides the weld line (Fukuda, 2001;Mathers, 2002). 52 Okamura et al (2004) studied a wide range of aluminium alloys, from 1000 to 8000 series, for FSW on similar and dissimilar material. It became clear from their research that joining dissimilar aluminium alloys, having different properties, is a challenging task.…”

Section: Introductionmentioning

confidence: 99%

Dissimilar alloys (AA6082/AA5083) joining by FSW and parametric optimization using Taguchi, grey relational and weight method

Jain¹,

Sharma²,

Gupta³

2018

10.5267/j.esm

View full text Add to dashboard Cite

This work is focused on the influence of different friction stir welding (FSW) parameters on AA6082 T-6 and AA5083-O alloys welding quality, by using Taguchi, Grey Relational and Weight Method. Four welding parameters were investigated, namely tool rotation speed (TRS), welding speed (WS), tool pin profile (TPP) and shoulder diameter (SD). The optimized setting of these input parameters was investigated so that weld parts quality could be optimized. Analysis of variance (ANOVA) was used to investigate the effects of these welding process parameters on response variables, viz. elongation (EL) and ultimate tensile strength (UTS). Single response optimization was carried using Taguchi Technique while grey relational analysis (GRA) was used for simultaneous optimization of two responses. Once the optimal settings of control factors were identified, confirmation experiments were performed for the validation of results. In the multi-response optimization, TRS was found to have the maximum effect (57.9%), followed by WS, SD and TPP. Weight method was applied for providing the priority to the response (i.e. EL and UTS). The response with higher priority presented a weight equal to 0.7, while the lower priority given corresponds to a weight of 0.3.

show abstract

“…In order to solve these problems, many studies of the dissimilar metal joining have been conducted such as resistance welding (Okita, 2004), laser welding (Katayama, 2004), explosive welding (Satou, 2004), friction stir welding (Okamura & Aota, 2004;Katoh & Tokisue, 2004), and diffusion bonding (Ohashi, 2004). As a result, solid-phase bonding is mainly put to practical use.…”

Section: Introductionmentioning

confidence: 99%