Lap Shear Adhesion of Styrenic Triblock Copolymers to Polypropylene and Polystyrene

Parsons, M.; Ernst, Andrea; Smyser, G.; Hiltner, A.; Baer, E.

doi:10.1080/00218469808009963

Cited by 2 publications

(4 citation statements)

References 22 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Recently, McGraw et al [21] have performed crazing measurements to probe the interdiffusion between two thin films of entangled polymers and showed that it takes less than one bulk reptation time to observe the structural characteristics of bulk crazes at the interface. Similar conclusions about the recovery of interfacial strength have been obtained from lap-joint shear tests [22][23][24][25]. These studies determined the ultimate shear stress at failure and correlated it with interdiffusion time.…”

supporting

confidence: 67%

“…As in previous simulations [32], we determined the interfacial strength using a shear test that is similar to a lap-joint shear experiment [22][23][24][25]. To focus on a region of width H near the interface, atoms in top (z > H/2) and bottom (z < −H/2) layers were held rigid and displaced at constant velocity in opposite directions in the xy−plane.…”

Section: Interface Simulationsmentioning

confidence: 99%

“…Recently, we have probed the interfacial strength of polymer interfaces in our molecular dynamics simulations [32,33] using a shear test that is similar to lapjoint shear experiments [22][23][24][25]. For miscible polymers, the interfacial strength increases with interdiffusion time, and saturates at the bulk strength.…”

mentioning

confidence: 99%

See 2 more Smart Citations

Healing of polymer interfaces: Interfacial dynamics, entanglements, and strength

Robbins

Perahia

et al. 2014

Phys. Rev. E

View full text Add to dashboard Cite

Self-healing of polymer films often takes place as the molecules diffuse across a damaged region, above their melting temperature. Using molecular dynamics simulations we probe the healing of polymer films and compare the results with those obtained for thermal welding of homopolymer slabs. These two processes differ from each other in their interfacial structure since damage leads to increased polydispersity and more short chains. A polymer sample was cut into two separate films that were then held together in the melt state. The recovery of the damaged film was followed as time elapsed and polymer molecules diffused across the interface. The mass uptake and formation of entanglements, as obtained from primitive path analysis, are extracted and correlated with the interfacial strength obtained from shear simulations. We find that the diffusion across the interface is significantly faster in the damaged film compared to welding because of the presence of short chains. Though interfacial entanglements increase more rapidly for the damaged films, a large fraction of these entanglements are near chain ends. As a result, the interfacial strength of the healing film increases more slowly than for welding. For both healing and welding, the interfacial strength saturates as the bulk entanglement density is recovered across the interface. However, the saturation strength of the damaged film is below the bulk strength for the polymer sample. At saturation, cut chains remain near the healing interface. They are less entangled and as a result they mechanically weaken the interface. Chain stiffness increases the density of entanglements, which increases the strength of the interface. Our results show that a few entanglements across the interface are sufficient to resist interfacial chain pullout and enhance the mechanical strength.

show abstract

supporting

confidence: 67%

Section: Interface Simulationsmentioning

confidence: 99%

See 1 more Smart Citation

Healing of polymer interfaces: Interfacial dynamics, entanglements, and strength

Robbins

Perahia

et al. 2014

Phys. Rev. E

View full text Add to dashboard Cite

show abstract

“…In recent work, we have used simulations to follow the evolution of the shear strength of interfaces between miscible and immiscible polymers . The maximum shear stress before failure σ max was evaluated using a geometry that mimics a lap-joint shear experiment. − As in experiments, we found that σ max rose with welding time t as t 1/4 and saturated long before polymers had diffused by their radius of gyration. In contrast to experiments, simulations allowed direct observations of the evolution of topological constraints (TCs) associated with entanglements.…”

Section: Introductionmentioning

confidence: 86%

Tensile Fracture of Welded Polymer Interfaces: Miscibility, Entanglements, and Crazing

Grest

Robbins

2014

Macromolecules

View full text Add to dashboard Cite

Large-scale molecular simulations are performed to investigate tensile failure of polymer interfaces as a function of welding time t. Changes in the tensile stress, mode of failure and interfacial fracture energy G I are correlated to changes in the interfacial entanglements as determined from Primitive Path Analysis. Bulk polymers fail through craze formation, followed by craze breakdown through chain scission. At small t welded interfaces are not strong enough to support craze formation and fail at small strains through chain pullout at the interface. Once chains have formed an average of about one entanglement across the interface, a stable craze is formed throughout the sample. The failure stress of the craze rises with welding time and the mode of craze breakdown changes from chain pullout to chain scission as the interface approaches bulk strength. The interfacial fracture energy G I is calculated by coupling the simulation results to a continuum fracture mechanics model. As in experiment, G I increases as * To whom correspondence should be addressed † Johns Hopkins University ‡ University of North Carolina ¶ Sandia National Laboratories 1 arXiv:1410.1917v1 [cond-mat.soft] 7 Oct 2014 t 1/2 before saturating at the average bulk fracture energy G b . As in previous simulations of shear strength, saturation coincides with the recovery of the bulk entanglement density. Before saturation, G I is proportional to the areal density of interfacial entanglements. Immiscibiltiy limits interdiffusion and thus suppresses entanglements at the interface. Even small degrees of immisciblity reduce interfacial entanglements enough that failure occurs by chain pullout and

show abstract

Lap Shear Adhesion of Styrenic Triblock Copolymers to Polypropylene and Polystyrene

Cited by 2 publications

References 22 publications

Healing of polymer interfaces: Interfacial dynamics, entanglements, and strength

Healing of polymer interfaces: Interfacial dynamics, entanglements, and strength

Tensile Fracture of Welded Polymer Interfaces: Miscibility, Entanglements, and Crazing

Contact Info

Product

Resources

About