Laser Triangulation in 3-Dimensional Granulometric Analysis

Abstract

LASER TRIANGULATION IN 3-DIMENSIONAL GRANULOMETRIC ANALYSIS TRIANGULACJA LASEROWA W TRÓJWYMIAROWYCH POMIARACH SKŁADU ZIARNOWEGOThe measurement of the particle size distribution plays an important role in mineral processing. Due to the high costs and time-consumption of the screening process, modern machine vision methods based on the acquisition and analysis of recorded photographic images. But the image analysis methods used so far, do not provide information on the three-dimensional shape of the grain. In the coal industry, the application scope of these methods is substantially limited by the low reflectivity of the black coal particle surface. These circumstances hinder proper segmentation of coal stream surface image. The limited information contained in two-dimensional image of the raw mineral stream surface, makes it difficult to identify proper size of grains partially overlapped by other particles and skewed particles. Particle height estimation based on the shadow length measurement becomes very difficult in industrial environment because of the fast movement of the conveyor belt and because of spatial arrangement of these particles, usually touching and overlapping. Method of laser triangulation connected with the movement of the conveyor belt makes it possible to create three-dimensional depth maps. Application of passive triangulation methods (e.g. stereovision) can be impeded because of the low contrast of the black coal on the black conveyor belt. This forces the use of active triangulation methods, directly identifying position of the analyzed image pixel. High contrast of the image can be obtained by a direct pointwise laser lighting. For the simultaneous identification of the entire section of the raw material stream it is useful to apply a linear laser (a planar sheet of the laser light). There have been presented basic formulas for conversion of pixel position on the camera CCD matrix to the real-word coordinates. A laboratory stand has been described. This stand includes a linear laser, two high-definition (2Mpix) cameras and stepper motor driver. The triangulation head moves on the rails along the belt conveyor section. There have been compared acquired depth maps and photographic images. Depth maps much better describe spatial arrangement of coal particles, and have a much lower noise level resulting from the specular light reflections from the shiny fragments of the particle surface. This makes possible an identification of the coal particles partially overlapped by other particles and obliquely arranged particles. It enables a partial elimination or compensation of image disturbances affecting the final result of the estimated particle size distribution. Because of the possibility of the reflected laser beam overriding by other particles it is advantageous to use a system of two cameras. Results of the experimental research confirmed the usefulness of the described method in spite of low reflectance factor of coal surface. The fast detection of changes in particle size distribution makes...

Bulk density estimation using a 3-dimensional image acquisition and analysis system

“…Volume estimation algorithms are much simpler then algorithms for calculation of the particle size distribution, because they do not require precise delineation of single touching and overlapping particles (this is usually the most complex, error-prone time-consuming task [4]). There is also no need to analyse the lower, usually invisible from the top, hemisphere of individual particle, because the lower surface of the whole particle population is well known (it is just the upper surface of the conveyor belt).…”

“…There are several methods of 3-dimensional image acquisition. The most applicable in these case are laser triangulation [4] and timeof flight cameras [5][6][7]. Each of these methods has its own advantages and disadvantages in terms of cost, efficiency and precision.…”

“…So, the selection of the method should adjusted to the type of the conveyor belt scale used in a particular application. If there is a single sensor scale measuring only one line, a laser triangulation system [4] presented in Fig. 2, should be used.…”

Machine vision monitoring and particle size feed analysis

“…On the basis of the research carried out, it is possible to distinguish as particularly efficient (because of the use of the rectilinear motion of the conveyor belt) the following 3-D image acquisition methods [8,11,12]:…”

Noise in Load Cell Signal in an Automatic Weighing System Based on a Belt Conveyor

“…The vision sensors are used for tracking and identifying an object moving on a conveyor belt [2][3][4], and range sensors are used for volume measurement [5]. The automatic weighing and sorting system is used in food and pharmaceutical industry where continuous and precise mass measurement of small objects is required [6,7].…”