Measurement and correlation studies of phase equilibria and thermophysical properties of 4-tert-butylbenzaldehyde

Kosuru, Ravi Kumar; Aniya, Vineet; Kumari, Aruna; Chitturi, Huldah Suharika; Sreeramoju, Aravindu; Thella, Prathap Kumar

doi:10.1016/j.molliq.2019.01.133

Cited by 6 publications

(6 citation statements)

References 24 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…18 Prior to the determination of viscosity, the survismeter is calibrated with a standard solution, i.e., water. A similar protocol was followed for viscosity measurement studies that were carried out previously in the same system in Kosuru et al 13 During the measurement of viscosity, standard uncertainty measured was 0.15 mPa s. 1 which also shows that the obtained equilibrium temperature is in good agreement with the literature. 4,7 The experimental saturated vapor pressures at their equilibrium temperatures were correlated using the Antoine equation employing the nonlinear regression based on Levenberg−Marquardt algorithm wherein chi-square minimization was used to calculate the Antoine constants, and the values are reported in Table 3.…”

Section: Methodssupporting

confidence: 60%

“…Additionally, the temperature of 60 °C is set to remove any traces of solvent left in the U-tube. A similar methodology for density measurement as detailed in our previous work Kosuru et al 13 was adapted in the present study. The standard uncertainty was determined to be 8 × 10 −4 g/ cm 3 for the density measurement.…”

Section: Methodsmentioning

confidence: 99%

“…The details of column and conditions used are reported in our previous studies. 13 Table 1 gives a clear representation of the chemicals used in the present study.…”

Section: Methodsmentioning

confidence: 99%

“…During the refractive index measurement, the standard uncertainty was evaluated to be 0.0002. The methodology and apparatus for measurement of the refractive index was previously presented in Kosuru et al 13 and Aniya et al 17 2.5. Viscosity Measurement.…”

Section: Methodsmentioning

confidence: 99%

“…2,6-Dichlorotoulene is purified by vacuum distillation and analyzed by GC (GC 2010 by Shimadzu Corporation) fitted with a flame ionization detector. The details of column and conditions used are reported in our previous studies Table gives a clear representation of the chemicals used in the present study.…”

Section: Methodsmentioning

confidence: 99%

See 4 more Smart Citations

Measurement and Correlation Studies of Phase Equilibria and Thermophysical Properties of 2,6-Dichlorotoluene

Bharadwaj,

Kumar,

Kommagalla

et al. 2024

J. Chem. Eng. Data

Self Cite

View full text Add to dashboard Cite

The present study summarizes the thermophysical properties and vapor pressure data of 2,6-dichlorotoluene, an important intermediate in the agrochemical industries for the production of herbicides. A Swietoslawski-type ebulliometer was used for generating the vapor pressure data experimentally in the range of 1.2−33.2 kPa. The vapor pressure data generated are correlated with the Antoine equation, and it is observed that the Antoine equation exhibited minimal deviations. The critical properties were also estimated using the group contribution methods, mainly Joback, Constantinou, Gani, and Nannoolal methods. The normal boiling point obtained using the Antoine equation is much closer to the boiling point obtained using the Constantinou and Gani method. Furthermore, the thermophysical properties like density, refractive index, and viscosity were experimentally evaluated at 95.5 kPa for the temperature ranging from 293.15 to 333.15 K. The density of the liquids was estimated using the Joback, Constantinou, Gani, and Nannoolal methods by employing the Rackett equation. It was observed that Joback showed the least relative average deviation of 1.442%. Mansingh viscometer is used to measure the viscosity and used the Vogel− Tamman−Fulcher equation for correlating the data and, on comparison, was found to be in good agreement. Apart from this, group contribution methods Nannoolal, Orrick, and Erbar methods were used to estimate the viscosity, wherein the Orrick and Erbar method showed the least deviation among the two. Other than the thermophysical properties and vapor pressure data for the pure component, i.e., 2,6-dichlorotoluene, vapor liquid equilibrium data for the binary system acetic acid (1) + 2,6-dichlorotoluene ( 2) is generated at three different subatmospheric pressures, 66.7, 60, and 40 kPa. NRTL model was used to fit the experimental data, and it was found that the experimental data are in good correlation with the predicted data. The binary interaction parameters for the NRTL model were reported, and T−x−y diagrams were also plotted, which show the experimental and predicted data. Thermodynamic consistency tests were conducted for the vapor−liquid equilibrium data at three different pressures, and it was observed that all of them have passed.

show abstract

Section: Methodssupporting

confidence: 60%

Section: Methodsmentioning

confidence: 99%

“…The details of column and conditions used are reported in our previous studies. 13 Table 1 gives a clear representation of the chemicals used in the present study.…”

Section: Methodsmentioning

confidence: 99%

Section: Methodsmentioning

confidence: 99%

Section: Methodsmentioning

confidence: 99%

See 3 more Smart Citations