Mechanical Properties Analysis of Kenaf–Grewia–Hair Fiber-Reinforced Composite

Boopathi, Sampath; Venkatesan, G.; Lewise, K. Anton Savio

doi:10.1007/978-981-16-9057-0_11

Cited by 27 publications

(2 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…With a beam specimen (500 × 100 × 100 mm) was tested for flexural strength according to IS 516 at 7, 28, and 90 days after curing according to ASTM-C293 standard [23][24][25]. A bending test fixture with two-point loading was used, consisting of two 38 mm diameter steel rollers spaced 133 mm apart.…”

Section: Flexural Strengthmentioning

confidence: 99%

Impact analysis of ceramic tile powder aggregates on self-compacting concrete

Harikaran¹,

Boopathi²,

Rajkannan³

et al. 2023

Eng. Res. Express

Self Cite

View full text Add to dashboard Cite

Waste ceramic tile (CT) powders are used to improve the workability, mechanical properties, and durability of self-compacting concrete (SCC). The waste CT powder is prepared by mixing construction tiles, sanitary fittings, and electrical insulators, with different weight percentages mixed into the SCC. Experiments have been conducted to evaluate the workability, mechanical, and durability of SCC. The optimum compressive, flexural, and tensile strengths were predicted to be 52.5 MPa, 8.5 MPa, and 7.8 MPa. SCC's durability and workability characteristics are achieved by mixing 50% CT powder, which increases interlocking properties and meets EFNARC standards. It is concluded that CT powder can be substituted for conventional fine aggregate in concrete, increasing compressive, flexural, and split tensile strengths by 12.5%, 9.33%, and 28.76% compared to conventional SCC. The 50% CT powder mixed SCC is the optimum value for achieving optimal mechanical, durability, and workability characteristics. Samples of 50% CT powder-mixed SCC with 7, 28, and 90 days of curing processes and microstructure are also illustrated.

show abstract

Section: Flexural Strengthmentioning

confidence: 99%

Impact analysis of ceramic tile powder aggregates on self-compacting concrete

Harikaran¹,

Boopathi²,

Rajkannan³

et al. 2023

Eng. Res. Express

Self Cite

View full text Add to dashboard Cite

show abstract

“…In addition, it has been discovered that employing thin sheets of the material instead of a single thick monolithic metal sheet can lower the growth rates of fatigue cracks in adhesively bonded sheet materials. In fiber metal laminates (FMLs), composite plies alternate with thin (0.3-0.5 mm thick) metal layers (Salve et al 2016, Eslami-Farsani et al 2022, Boopathi et al 2023. The metal layers are given a particular surface treatment to ensure proper adhesion, and high-strength fibers that have already been pre-impregnated with resin are utilized to create composite layers with a unidirectional, cross-ply, or fabric structure.…”

Section: Introductionmentioning

confidence: 99%

Investigation of the mechanical behaviour of hybrid fiber reinforced composite with aluminium laminates

Ramesh¹,

M²

2023

Phys. Scr.

View full text Add to dashboard Cite

The present study investigates the mechanical characteristics of a hybrid fiber-reinforced composite with aluminium laminates (HFRCAL). The hybrid composite specimens were fabricated by hand layup method including the epoxy as a Matrix material, with Al6061-T6 as the outer layers, while Kevlar-29, carbon fiber, basalt fiber, and E-glass fiber act as hybrid reinforcing laminates with varying order of arrangement. The prepared laminate composites were tested for performance under tensile, flexural, and impact loading conditions. Three combinations of the laminate composites were tested, namely the Al/K/C/E/B/K/Al (Al+5KH+Al), Al/C/B/E/K/C/Al (Al+5CH+Al), and Al/B/C/E/K/B/Al (Al+5BH+Al) composition laminates. Among the tested specimens, it was found that the Al+5KH+Al laminate composite exhibited the highest yield strength of 220 MPa, and Ultimate tensile strength (UTS) of 245 MPa. These were 11.53% and 11.2% higher than those of Al+5CH+Al, while Al+5BH+Al exhibited the lowest UTS of 202 MPa. During flexural loading, the Al+5CH+Al showed the highest flexural strength of 305.6 MPa which was 35.5% higher than that of Al+5BH+Al and 38.33% higher than the flexural strength of Al+5KH+Al. The impact strength of Al+5KH+Al was higher by 5.74% and 11.73% of Al+5CH+Al and Al+5BH+Al respectively.

show abstract

Experimental Study on Mechanical Strength and Durability of E-waste Mixed Concrete

Boopathi

2024

Lecture Notes in Mechanical Engineering

View full text Add to dashboard Cite

Mechanical Properties Analysis of Kenaf–Grewia–Hair Fiber-Reinforced Composite

Cited by 27 publications

References 20 publications

Impact analysis of ceramic tile powder aggregates on self-compacting concrete

Impact analysis of ceramic tile powder aggregates on self-compacting concrete

Investigation of the mechanical behaviour of hybrid fiber reinforced composite with aluminium laminates

Experimental Study on Mechanical Strength and Durability of E-waste Mixed Concrete

Contact Info

Product

Resources

About