Melt Processable Novolac Cyanate Ester/Biphenyl Epoxy Copolymer Series with Ultrahigh Glass-Transition Temperature

Abstract

The rapid progress in silicon carbide (SiC)-based technology for high-power applications expects an increasing operation temperature (up to 250 °C) and awaits reliable packaging materials to unleash their full power. Epoxy-based encapsulant materials failed to provide satisfactory protection under such high temperatures due to the intrinsic weakness of epoxy resins, despite their unmatched good adhesion and processability. Herein, we report a series of copolymers made by melt blending novolac cyanate ester and tetramethylbiphenyl epoxy (NCE/EP) that have demonstrated much superior hightemperature stability over current epoxies. Benefited from the aromatic, rigid backbone and the highly functional nature of the monomers, the highest values achieved for the copolymers are as follows: glass-transition temperature (T g ) above 300 °C, decomposition onset above 400 °C, and char yield above 45% at 800 °C, which are among the highest of the known epoxy chemistry by far. Moreover, the high-temperature aging (250 °C) experiments showed much reduced mass loss of these copolymers compared to the traditional high-temperature epoxy and even the pure NCE in the long term by suppressing hydrolysis degradation mechanisms. The copolymer composition, i.e., NCE to EP ratio, has found to have profound impacts on the resin flowability, thermomechanical properties, moisture absorption, and dielectric properties, which are discussed in this paper with in-depth analysis on their structure−property relationships. The outstanding high-temperature stability, preferred and adjustable processability, and the dielectric properties of the reported NCE/EP copolymers will greatly stimulate further research to formulating robust epoxy molding compounds (EMCs) or underfill for packaging next-generation high-power electronics.

Development of Molding Compounds Based on Epoxy Resin/Aromatic Amine/Benzoxazine for High‐Temperature Electronic Packaging Applications

“…The high T g (above 200 °C) signifies that the polymer network of oxidized MC EDB is in glassy state and the chain segmental motion is not active at 200 °C, which imposes dynamic constraints on the diffusion of oxygen, the propagation of free radicals, and the volatilization of chain scission products. [ 9 ] As for the oxidized MC EDB (5/1.5/11) sample, the external oxygen can easily invade the polymer network from the defects, thus leading to an aggravated thermal‐oxidative degradation.…”

Melamine–graphene epoxy nanocomposite based die attach films for advanced 3D semiconductor packaging applications

“…A more fundamental estimation of cross-link density was calculated by the following equation in the epoxy's rubbery region: 49,50 where X is the estimated cross-link density, R is the ideal gas constant ( R = 8.314 J (mol K) −1 , E ′ is the storage modulus at T ′, and T ′ is 30 °C higher than T g . With the ratio of bisA to cresol novolac epoxy decreasing, the calculated cross-link density is increased.…”

High heat‐resistant (250°C) epoxy resin composites with excellent dielectric properties

“…Over these years, a lot of works has been done to modify epoxy by inorganic fillers. Yue et al 11 found the T g of epoxy increased from 257 to 275°C with a BN content of 30 wt% 10 . Chen et al 12 reported that the T g of epoxy increased from 103.5 to 132.1°C containing 20 wt% micro‐AlN particles and 3 wt% nano‐AlN particles.…”

“…Yue et al 11 found the T g of epoxy increased from 257 to 275 C with a BN content of 30 wt%. 10 Chen et al 12 reported that the T g of epoxy increased from 103.5 to 132.1 C containing 20 wt% micro-AlN particles and 3 wt% nano-AlN particles. Guo et al discovered that ZnO could increased T g of epoxy from 191.7 to 201.96 C when the filling rate is 50 wt%.…”