Microwave Kinetic Inductance Detectors

Mazin, Benjamin A.

doi:10.1142/9789811203787_0002

Cited by 12 publications

(9 citation statements)

References 89 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…This comes at the cost of larger footprint on chip and higher complexity. Furthermore, instead of lumped element resonators, distributed resonators can be used, exhibiting much lower spread < 0.1% [32], also at the cost of larger footprint, c.f. [4].…”

Section: Parameter Spread Sensitivitymentioning

confidence: 99%

Vulnerability to Parameter Spread in Josephson Traveling-Wave Parametric Amplifiers

Kissling¹,

Gaydamachenko²,

Kaap³

et al. 2023

Preprint

View full text Add to dashboard Cite

We analyze the effect of circuit parameter variation on the performance of Josephson traveling-wave parametric amplifiers (JTWPAs). Specifically, the JTWPA concept we investigate is using flux-biased nonhysteretic rf-SQUIDs in a transmission line configuration, which harnesses the three-wave mixing (3WM) regime. Dispersion engineering enables phasematching to achieve power gain of ∼20 dB, while suppressing the generation of unwanted mixing processes. Two dispersion engineering concepts using a 3WM-JTWPA circuit model, i.e., resonant phase-matching (RPM) and periodic capacitance modulation (PCM), are discussed, with results potentially also applicable to four-wave-mixing (4WM) JTWPAs. We propose suitable circuit parameter sets and evaluate amplifier performance with and without circuit parameter variance using transient circuit simulations. This approach inherently takes into account microwave reflections, unwanted mixing products, imperfect phasematching, pump depletion, etc. In the case of RPM the resonance frequency spread is critical, while PCM is much less sensitive to parameter spread. We discuss degrees of freedom to make the JTWPA circuits more tolerant to parameter spread. Finally, our analysis shows that the flux-bias point where rf-SQUIDs exhibit Kerr-free nonlinearity is close to the sweet spot regarding critical current spread.

show abstract

Section: Parameter Spread Sensitivitymentioning

confidence: 99%

Vulnerability to Parameter Spread in Josephson Traveling-Wave Parametric Amplifiers

Kissling¹,

Gaydamachenko²,

Kaap³

et al. 2023

Preprint

View full text Add to dashboard Cite

show abstract

“…Kinetic inductance detectors [1][2][3][4] (KIDs) are planar superconducting resonators that have a sensing element designed to absorb photons. If the energy of an absorbed photon is greater than two times the superconducting energy gap of the material, then that photon will break one or more Cooper pairs in the device.…”

Section: Introductionmentioning

confidence: 99%

A Scalable Cryogenic LED Module for Selectively Illuminating Kinetic Inductance Detector Arrays

Shroyer¹,

Nelson²,

Walters³

et al. 2022

Preprint

View full text Add to dashboard Cite

We present the design and measured performance of an LED module for spatially mapping kinetic inductance detector arrays in the laboratory. Our novel approach uses a multiplexing (MUX) scheme that only requires seven wires to control 480 red LEDs, and the number of LEDs can be scaled up without adding any additional wires. This multiplexing approach relies on active surface mount components that can operate at cryogenic temperatures down to 10 K. Cryogenic tests in liquid nitrogen and inside our cryostat demonstrate that the MUX circuit works at 77 K and 10 K, respectively. The LED module presented here is tailored for millimeter-wave detector modules we are developing, but the approach could be broadly useful for other KID-based detector systems.

show abstract

“…Recently an R E of ≈ 55 at 402nm 11 has been demonstrated. For examples of phase-time streams and more details on MKIDs see 9,[12][13][14] .…”

Section: Introduction 11 Microwave Kinetic Inductance Detectors and K...mentioning

confidence: 99%

What could KIDSpec, a new MKID spectrograph, do on the ELT?

Hofmann

O’Brien

Geng

2022

Ground-Based and Airborne Instrumentation for Astronomy IX

View full text Add to dashboard Cite

Microwave Kinetic Inductance Detectors (MKIDs) are beginning to become more prominent in astronomical instrumentation, due to their sensitivity, low noise, high pixel count for superconducting detectors, and inherent energy and time resolving capability. The Kinetic Inductance Detector Spectrometer (KIDSpec) will take advantage of these features, KIDSpec is a medium resolution MKID spectrograph for the optical/near infrared. KIDSpec will contribute to many science areas particularly those involving short and/or faint observations. When short period binary systems are found, typical CCD detectors will struggle to characterise these systems due to the very short exposures required, causing errors as large as the estimated parameter itself. The KIDSpec Simulator (KSIM) has been developed to investigate how much KIDSpec could improve on this. KIDSpec was simulated on an ELT class telescope to find the extent of its potential, and it was found that KIDSpec could observe a m V ≈ 24 with an SNR of 5 for a 10s exposure at 1420 spectral resolution. This would mean that KIDSpec on an ELT class telescope could spectroscopically follow up on any LSST photometric discoveries of LISA verification sources.

show abstract

Microwave Kinetic Inductance Detectors

Cited by 12 publications

References 89 publications

Vulnerability to Parameter Spread in Josephson Traveling-Wave Parametric Amplifiers

Vulnerability to Parameter Spread in Josephson Traveling-Wave Parametric Amplifiers

A Scalable Cryogenic LED Module for Selectively Illuminating Kinetic Inductance Detector Arrays

What could KIDSpec, a new MKID spectrograph, do on the ELT?

Contact Info

Product

Resources

About