Modelling and empirical development of an anti/de-icing approach for wind turbine blades through superposition of different types of vibration

Habibi, Hossein; Edwards, Graham; Sannassy, Caumaghen; Kappatos, Vassilios; Lage, Yoann; Stein, Jasmin; Selcuk, Cem; Gan, Tat-Hean

doi:10.1016/j.coldregions.2016.04.012

Cited by 23 publications

(10 citation statements)

References 11 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…To prevent or to suppress the ice build-up, researchers and engineers have made a great deal of effort to understand the physicochemical mechanisms of freezing, and developed many anti/de-icing strategies over the last decades [18][19][20]. Some typical de-icing approaches, such as vapor heating, electro-thermally melting, and mechanical vibration, have been optimized and widely used in the above fields [21][22][23][24]. However, these active de-icing methods usually rely on continuously heating or intermittent vibration of the frozen locations with huge energy consumption, and the corresponding equipment / systems are also difficult to design and manufacture, therefore these strategies should be avoided or minimized in the future whenever possible [25,26].…”

Section: Introductionmentioning

confidence: 99%

Icephobic materials: Fundamentals, performance evaluation, and applications

Shen

Tao

et al. 2019

Progress in Materials Science

324

166

View full text Add to dashboard Cite

Section: Introductionmentioning

confidence: 99%

Icephobic materials: Fundamentals, performance evaluation, and applications

Shen

Tao

et al. 2019

Progress in Materials Science

324

166

View full text Add to dashboard Cite

“…Ultrasonic generates shear stress to remove ice accumulated on the blade and low frequency vibration increases sufficient stress in a short time. The combination of the two will cause the ice to fall off …”

Section: Anti‐ice System and De‐icing Systemmentioning

confidence: 99%

“…The combination of the two will cause the ice to fall off. 115 Ultrasonic deicing has been proven by many scholars to be achievable. Ultrasonic deicing is superior to other deicing methods.…”

Section: Ultrasonicmentioning

confidence: 99%

A review on ice detection technology and ice elimination technology for wind turbine

et al. 2019

View full text Add to dashboard Cite

Blade icing can affect wind turbines to generate electricity. In severe cases, 30% of power generation is lost in a year, and safety problems in the vicinity of wind power plants are also caused. Researchers have designed anti-icing and de-icing technologies to reduce these effects, and excellent ice-detecting devices are a prerequisite for using anti-icing and de-icing technologies. Ultrasonic attenuation technology can effectively and reliably detect the presence of ice without affecting the aerodynamic performance of the blade, providing a reliable guarantee for anti-icing and de-icing systems. Deicing and anti-icing systems are divided into active and passive, active heating blades are still the most effective anti-icing and de-icing methods, but their energy consumption is too high. Although there are many existing de-icing methods, there are not many practical uses. This article introduces them separately and lists their advantages and disadvantages. The use of ultrasonic anti-icing and de-icing is an economical and reliable means that has been proven to be used for anti-icing and de-icing of blades. However, under normal circumstances, a single anti-icing de-icing system cannot completely solve the problem of icing of the blades. This paper suggests using both ultrasonic and hydrophobic coatings to cope with more icing conditions. K E Y W O R D Santi-icing and deicing technology, fan blade, hydrophobic coating, ice detection technology, ultrasonic deicing | INTRODUCTIONWith the rapid development of the world economy, lots of countries are increasingly demanding energy resources. Owing to release a lot of greenhouse gases, chemicals and toxins substances from the combustion of the fossil fuels such as coal and oil, 1 People began to look for renewable energy to provide energy consumption, such as wind energy, 2-4 hydrogen energy, 5-7 solar energy, 8-10 biogas and biomass energy. 11-15 With the wind power growing rapidly, generate electricity by using wind turbines is economical and environmentally friendly. 16 As can be seen in Figure 1, China's total installed capacity of wind turbines in 2016 is much higher than in other countries.China has the largest wind power market in the country, and the installed capacity of wind power is growing steadily year by year. The high density of air is conducive to the development of wind energy resources in cold regions. Figure 2 shows wind resource changes in different seasons. The wind speed from June to August is significantly lower than other months. There are also data showing that wind resources in cold regions are 10% higher than other regions. 17,18

show abstract

“…In the case of operated carriers, it also lowers maneuverability, thus increasing the risk of accidents. The most common commercial deicing solutions consist of infrared or electrothermal melting, 3 addition of low-freezing point agents, 4 pneumatic actuation, 5 and mechanical vibration, 6 which require a high energy demand and need to be engineered for specific applications rather than offering a broadband solution.…”

Section: Introductionmentioning

confidence: 99%

A Simple Approach for Flexible and Stretchable Anti-icing Lubricant-Infused Tape

Carlotti

Cesini

Mattoli

2021

ACS Appl. Mater. Interfaces

View full text Add to dashboard Cite

Unwanted icing has major safety and economic repercussions on human activities, affecting means of transportation, infrastructures, and consumer goods. Compared to the common deicing methods in use today, intrinsically icephobic surfaces can decrease ice accumulation and formation without any active intervention from humans or machines. However, such systems often require complex fabrication methods and can be costly, which limits their applicability. In this study, we report the preparation and characterization of several slippery lubricant-infused porous surfaces (SLIPSs) realized by impregnating with silicone oil a candle soot layer deposited on double-sided adhesive tape. Despite the use of common household items, these SLIPSs showed anti-icing performance comparable to other systems described in the literature (ice adhesion < 20 kPa) and a good resistance to mechanical and environmental damages in laboratory conditions. The use of a flexible and functional substrate as tape allowed these devices to be stretchable without suffering significant degradation and highlights how these systems can be easily prepared and applied anywhere needed. In addition, the possibility of deforming the substrate can “allow” the application of SLIPS technology in mechanical ice removal methodologies, drastically incrementing their performance.

show abstract

Modelling and empirical development of an anti/de-icing approach for wind turbine blades through superposition of different types of vibration

Cited by 23 publications

References 11 publications

Icephobic materials: Fundamentals, performance evaluation, and applications

Icephobic materials: Fundamentals, performance evaluation, and applications

A review on ice detection technology and ice elimination technology for wind turbine

A Simple Approach for Flexible and Stretchable Anti-icing Lubricant-Infused Tape

Contact Info

Product

Resources

About