Modelling and Simulation of Variable Frequency Synchronous DC-DC Buck Converter

Renius, Jeya Selvan; Kumar, K. Vinoth; Fredderics, Arnold; Guru, Raja; Nair, Sree Lakshmi

doi:10.11591/ijpeds.v5i2.6472

Cited by 3 publications

(2 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Then, Fourier coefficients of the input function (3) were calculated in (4). By assuming that q = jn and substituting (2), (9), and (10) into (6), the proposed equation of buck converter can be expressed as follows.…”

Section: Buck Converter Analysismentioning

confidence: 99%

See 1 more Smart Citation

Accurate Symbolic Steady State Modeling of Buck Converter

Setiawan¹,

Hirata²,

Hodaka³

2017

IJECE

View full text Add to dashboard Cite

Steady state analysis is fundamental to any electric and electronic circuit design. Buck converter is one of most popular power electronics circuit and has been analyzed in various situations. Although the behavior of buck converters can be understood approximately by the well-known state space averaging method, little is known in the sense of detailed behavior or exact solution to equations. In this paper a steady state analysis of buck converter is proposed which allows the exact calculation of steady state response. Our exact solution is expressed as a Fourier series. Our result is compared with numerical calculation to be verified. Our method copes with more complicated problems such as describing average power and root-mean-square power that are most critical issues in power electronics circuit.Copyright c 2017 Institute of Advanced Engineering and Science.All rights reserved.Corresponding Author: Ichijo Hodaka Department of Environmental Robotics, University of Miyazaki 1-1, Gakuen Kibanadai-nishi, Miyazaki, 889-2192, Japan Phone: +81 985 587 352 E-mail: hijhodaka[at]cc.miyazaki-u.ac.jp INTRODUCTIONAn analysis of steady-state response of a system is important key in circuit design and control, included dc-dc converter. In convential method, the steady state of dc-dc converter is assumed as the constant value. Many researches based on state space averaging method and high switching frequency assumption observe steady state response [1,2,3,4,5]. The method gives simple way to analyze but some ripples are undescribed clearly. The power electronic handbook approximate linear ripple to analyze dc-dc converter more accurately [6]. The approximation may be correct if the switching frequency is high. Since there are some limitation in component, some high frequency is not always reached.The importance of accurate steady-state analysis has already noticed in many researches [7,8,9,10,11,12]. A significant part of the design of circuits requires the simulation of the steady-state response. Parameters such as the gain, harmonic distortion and the input and output impedances are studied in the steady-state mode of operation [7]. Using conventional time-stepping simulations and waiting-time for possible steady state is often not practical because in most cases the time constants of the modes are much larger than the switching period [8]. In conventional method of dc-dc converter analysis, steady state ripple values are negligible, compared to the steady state values themselves. Switching power converters are inherently nonlinear and consequently it is very difficult to calculate the root-mean-square (RMS) values of the state variable ripple. These RMS values are important in order to calculate the current stresses of the different power converter devices as well as to filter design in order to meet the given specifications [9]. Though power electronic handbook [6] shows the RMS calculation using approximation linear ripple, the result is not absolutely correct due to linear approximation. In order to achieve a ...

show abstract

Section: Buck Converter Analysismentioning

confidence: 99%

“…In convential method, the steady state of dc-dc converter is assumed as the constant value. Many researches based on state space averaging method and high switching frequency assumption observe steady state response [1,2,3,4,5]. The method gives simple way to analyze but some ripples are undescribed clearly.…”

Section: Introductionmentioning

confidence: 99%

Accurate Symbolic Steady State Modeling of Buck Converter

Setiawan¹,

Hirata²,

Hodaka³

2017

IJECE

View full text Add to dashboard Cite

show abstract

Steady state symbolic analysis of buck converter using fourier series

Setiawan

Hirata

Hodaka

2017

2017 2nd International Conference on Frontiers of Sensors Technologies (ICFST)

View full text Add to dashboard Cite

Development and Simulation of Stand Alone Photovoltaic Model Using Matlab/Simulink

Sharma¹,

Pal²,

Singh³

et al. 2015

IJPEDS

View full text Add to dashboard Cite

This paper presents the implementation of a generalized photovoltaic model using Matlab/Simulink software package, which can be representative of PV cell, module for easy use on simulation platform. The proposed model is designed with a user-friendly icon and a dialog box like Simulink block libraries which makes the generalized PV model easily simulated and analyzed in conjunction with power electronics. Taking the effect of sunlight irradiance and cell temperature into consideration, the output current and power characteristics of PV model are simulated and optimized using the proposed model. The proposed model enables the dynamics of PV power system to be easily simulated, analyzed and optimized. Keyword:Array Matlab/Simulink Module Photovoltaic Photovoltaic

show abstract

Modelling and Simulation of Variable Frequency Synchronous DC-DC Buck Converter

Cited by 3 publications

References 0 publications

Accurate Symbolic Steady State Modeling of Buck Converter

Accurate Symbolic Steady State Modeling of Buck Converter

Steady state symbolic analysis of buck converter using fourier series

Development and Simulation of Stand Alone Photovoltaic Model Using Matlab/Simulink

Contact Info

Product

Resources

About