Module System Developing of Computer-Aided Engineering for Process Technologies with Ball-Shaft Hardener

Tamarkin, M. A.; Tishchenko, E. E.; Astashkin, Aleksey; Tishchenko, Roman

doi:10.1007/978-3-031-11058-0_163

Cited by 3 publications

(2 citation statements)

References 18 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Следует отметить, что широкому распространению многих методов ППД в промышленности препятствует слабая изученность их основных закономерностей, трудности, возникающие в процессе проектирования оптимальных сочетаний режимов обработки и конструктивных параметров средств технологического оснащения. Во многих случаях режимы обработки назначаются исходя из результатов частных экспериментальных исследований, что приводит к низкой эффективности обработки [1][2][3][4][5][6].…”

unclassified

“…Повороты корпуса упрочнителя в процессе колебанийРезультаты исследования. Чтобы установить основные закономерности влияния технологических параметров процесса на взаимодействие осциллирующего индентора с обрабатываемой поверхностью необходимо учитывать кинетическую энергию индентора, количество инденторов, радиус индентора, коэффициент полезного действия устройства, физико-механические свойства обрабатываемой детали[1][2][3][4][5][6].…”

unclassified

See 1 more Smart Citation

Surface Quality Forming under Parts Finishing and Strengthening Treatment with an Eccentric Hardener

Tamarkin,

Tishchenko,

Hashash

2023

Vestnik Donskogo gosudarstvennogo tehničeskogo universiteta

Self Cite

View full text Add to dashboard Cite

Introduction. The formation of the quality parameters of the surface layer and the operational properties of the parts occurs throughout all stages of their manufacture. However, the decisive impact is most often exerted by the stages of finishing. Therefore, in modern digital engineering, the task of process support of high quality of the surface layer of the part is one of the challenges in solving the problem of improving the quality and reliability and increasing the life cycle of manufactured machines. Surface plastic deformation treatment is instrumental in improving the performance characteristics of machine parts. Its essence is that the required quality parameters of parts are obtained not by removing a layer of material, but by plastic deformation. During the processing, both the dimensions of the parts and the physical and mechanical properties of the surface layers are changed. In this case, the technologist has the opportunity to significantly increase the life cycle of the manufactured products through controlling the process. These studies are aimed at providing the required quality parameters of the surface layer under processing with an eccentric hardener.Materials and Methods. The article presents the results of research on a new method of surface plastic deformation treatment – with an oscillating eccentric hardener. The considered processing method enables to obtain high quality of the treated surface, to process large-sized parts in places that are stress concentrators, to process welds, small areas of surfaces, whose hardening is needed for the part to fulfill its intended service. A set of theoretical studies was carried out; their results provided determining the parameters of a single interaction of the indenter and the surface of the part, the diameter of the plastic imprint and its depth.Results. Dependences for determining the surface roughness, the depth of the hardened layer and the degree of deformation were obtained. The resulting formulas were tested for adequacy by experimental studies.Discussion and Conclusion. The obtained research results can be used in the technological design of surface plastic deformation treatment processes. Further tasks for the study of the considered processing method are determined.

show abstract

unclassified

Surface Quality Forming under Parts Finishing and Strengthening Treatment with an Eccentric Hardener

Tamarkin,

Tishchenko,

Hashash

2023

Vestnik Donskogo gosudarstvennogo tehničeskogo universiteta

Self Cite

View full text Add to dashboard Cite

show abstract

Quality Surface Forming During Parts Strengthening-Finishing Treatment with Oscillatory Tool

Tamarkin,

Tishchenko,

Astashkin

2024

Lecture Notes in Networks and Systems

View full text Add to dashboard Cite

Optimization of Strengthening Treatment of Parts With an Oscillating Tool

Tamarkin,

Tischenko,

Hashash

et al. 2023

Transport Engineering

View full text Add to dashboard Cite

The research objective is to study the technological capabilities and develop methods for designing highly efficient technological processes of strengthening treatment of parts with an oscillating tool - an eccentric strengthener. The tasks are theoretical modeling of the the oscillating tool processing dynamics, theoretical modeling and experimental studies of forming surface roughness, the depth of the strengthened layer and the degree of parts deformation during treatment with an oscillating tool, as well as the development of a technique for designing high-efficiency technological processes. A new method of machining parts by surface plastic deformation is proposed. The dependences of the influence of treatment modes, design characteristics of the equipment and physical and mechanical properties of treated part materials on the quality parameters of the surface layer (surface roughness, depth of the strengthened layer and the degree of deformation) are obtained. The dependence for determining the treatment time is presented. The theoretical dependences obtained are experimentally verified and found to be adequate according to the results of experimental studies. The regularities of designing technological processes ensuring an increase in the operational properties of the machined parts are developed. An engineering calculation technique of optimal parameters of technological processes for machining parts with an oscillating tool is developed in order to increase their operational properties. A method for optimizing the technological processes of machining parts with an oscillating tool is proposed. A software product is developed that allows performing technological design using microprocessor technology.

show abstract

Module System Developing of Computer-Aided Engineering for Process Technologies with Ball-Shaft Hardener

Cited by 3 publications

References 18 publications

Surface Quality Forming under Parts Finishing and Strengthening Treatment with an Eccentric Hardener

Surface Quality Forming under Parts Finishing and Strengthening Treatment with an Eccentric Hardener

Quality Surface Forming During Parts Strengthening-Finishing Treatment with Oscillatory Tool

Optimization of Strengthening Treatment of Parts With an Oscillating Tool

Contact Info

Product

Resources

About