Numerical investigation on the effect of bileaflet mechanical heart valve's implantation tilting angle and aortic root geometry on intermittent regurgitation and platelet activation

Abstract

Platelet activation induced by shear stresses and non-physiological flow field generated by bileaflet mechanical heart valves (BMHVs) leads to thromboembolism, which can cause fatal consequences. One of the causes of platelet activation could be intermittent regurgitation, which arises due to asynchronous movement and rebound of BMHV leaflets during the valve closing phase. In this numerical study, the effect of intermittent regurgitation on the platelet activation potential of BMHVs was quantified by modeling a BMHV in the straight and anatomic aorta at implantation tilt angles 0°, 5°, 10°, and 20°. A fully implicit Arbitrary Lagrangian-Eulerian-based Fluid-Structure Interaction formulation was adopted with blood modeled as a multiphase, non-Newtonian fluid. Results showed that the intermittent regurgitation and consequently the platelet activation level increases with the increasing implantation tilt of BMHV. For the straight aorta, the leaflet of the 20° tilted BMHV underwent a rebound of approximately 20° after initially closing, whereas the leaflet of the 10°, 5°, and 0° tilted BMHVs underwent a rebound of 8.5°, 3°, and 0°, respectively. For the anatomic aorta, the leaflet of the 20° tilted BMHV underwent a rebound of approximately 24° after initially closing, whereas the leaflet of the 10°, 5°, and 0° tilted BMHVs underwent a rebound of 14°, 10°, and 7°, respectively. For all the implantation orientations of BMHVs, intermittent regurgitation and platelet activation were always higher in the anatomic aorta than in the straight aorta. The study concludes that the pivot axis of BMHV must be implanted parallel to the aortic root's curvature to minimize intermittent regurgitation and platelet activation. K E Y W O R D Saortic root geometry, bileaflet mechanical heart valve, implantation tilting angle, intermittent regurgitation, platelet activation

Evaluating medical device and material thrombosis under flow: current and emerging technologies

“…3A), 69 stents, 110,111 and mechanical valves (Fig. 3B) 115,125 have been widely modelled using CFD simulations, as have ex vivo devices and tubing systems. 126 CFD simulations of more geometrically complex medical devices such as ECMO 108 and LVADs (Fig.…”

Simulation of Mechanical Heart Valve Dysfunction and the Non-Newtonian Blood Model Approach

“…However, in recent years, several authors performed numerical studies on MHV dysfunction [ 2 , 3 , 7 , 25 , 34 – 37 ], and the simulation results show a significant difference from the normal MHV. The non-Newtonian viscosity model plays a role in numerical studies of blood flow through the MHV due to the complex structure of MHV [ 29 – 31 , 36 , 38 – 41 ].…”

State-of-the-art numerical fluid–structure interaction methods for aortic and mitral heart valves simulations: A review

“…Despite these problems, ALE has been widely used to simulate the FSI between leaflets of the heart valves and cardiac blood flow simply due to its accurate prediction of cardiac mechanics and flow parameters near the BLI, thereby outperforming fixed-grid methods. 112,141,200,217,223,224 The cut cell method is another variant of moving mesh, where the Cartesian mesh is adapted to the moving boundary by recursive reshaping of only the fluid cells that are cut by the fluid–structure interface and has been mainly employed for aortic valves simulations with contact modeling. 12,119,121 However, due to multiple possibilities of shapes the reshaped cells can take, it becomes difficult to apply the cut cell method to three-dimensional moving boundaries.…”

“…103 This approach has greater potential to capture novel details of the continuum than that of a purely Lagrangian or Eulerian approach. 104,105…”