Search citation statements
Paper Sections
Citation Types
Year Published
Publication Types
Relationship
Authors
Journals
Two-phase flow of oil and water is commonly observed in wellbores, and its behavior under a wide range of flow conditions and inclination angles constitutes a relevant unresolved issue for the petroleum industry. Among the most significant applications of oil-water flow in wellbores are production optimization, production string selection, production logging interpretation, down-hole metering, and artiflcial lift design and modeling. In this study, oil-water flow in vertical and inclined pipes has been investigated theoretically and experimentally. The data are acquired in a transparent test section (0.0508 m id., 15.3 m long) using a mineral oil and water {po/p^ = 0.85, MO/MW = 20.0 & Oo-^ = 33.5 dyne/cm at 32.22° C). The tests covered inclination angles of 90, 75, 60, and 45 deg from horizontal. The holdup and pressure drop behaviors are strongly affected by oil-water flow patterns and inclination angle. Oilwater flows have been grouped into two major categories based on the status of the continuous phase, including water-dominated and oil-dominated flow patterns. Waterdominated flow patterns generally showed significant slippage, but relatively low frictional pressure gradients. In contrast, oil-dominated flow patterns showed negligible slippage, but significantly large frictional pressure gradients. A new mechanistic model is proposed to predict the water holdup in vertical wellbores based on a driftflux approach. The drift flux model was found to be adequate to calculate the holdup for high slippage flow patterns. New closure relationships for the two-phase friction factor for oil-dominated and water-dominated flow patterns are also proposed. Introductory RemarksIn the petroleum industry, multiphase flow is a common occurence in production of oil and gas. Two-phase flow of oil and water is commonly encountered in wellbores; however, its hydro-dynamic behavior under a wide range of flow conditions and inclination angles constitutes a relevant unresolved issue for the oil industry.Multiphase flows are characterized by the existence of diverse flow configurations or flow patterns, which can usually be identified by a typical geometrical arrangement of the phases in the pipe. Inherent to each flow pattern are a characteristic spatial distribution of the interface, flow mechanisms, and distinctive values for design parameters such as pressure gradient, holdup, and heat transfer coefficient. There is clear evidence that accurate knowledge of the oil-water flow patterns, their ranges of existence as a function of flow rates and pipe inclination angles, are crucial in predicting many hydrodynamic parameters. These include pressure gradient and holdup in a number of production engineering applications, such as production optimization, optimum string selection, production logging interpretation, downhole metering, and artificial lift design and modeling.A fundamental problem in production engineering is to determine the actual volumetric flow rates of each of the phases flowing at any location in the wellbore. This in...
Two-phase flow of oil and water is commonly observed in wellbores, and its behavior under a wide range of flow conditions and inclination angles constitutes a relevant unresolved issue for the petroleum industry. Among the most significant applications of oil-water flow in wellbores are production optimization, production string selection, production logging interpretation, down-hole metering, and artiflcial lift design and modeling. In this study, oil-water flow in vertical and inclined pipes has been investigated theoretically and experimentally. The data are acquired in a transparent test section (0.0508 m id., 15.3 m long) using a mineral oil and water {po/p^ = 0.85, MO/MW = 20.0 & Oo-^ = 33.5 dyne/cm at 32.22° C). The tests covered inclination angles of 90, 75, 60, and 45 deg from horizontal. The holdup and pressure drop behaviors are strongly affected by oil-water flow patterns and inclination angle. Oilwater flows have been grouped into two major categories based on the status of the continuous phase, including water-dominated and oil-dominated flow patterns. Waterdominated flow patterns generally showed significant slippage, but relatively low frictional pressure gradients. In contrast, oil-dominated flow patterns showed negligible slippage, but significantly large frictional pressure gradients. A new mechanistic model is proposed to predict the water holdup in vertical wellbores based on a driftflux approach. The drift flux model was found to be adequate to calculate the holdup for high slippage flow patterns. New closure relationships for the two-phase friction factor for oil-dominated and water-dominated flow patterns are also proposed. Introductory RemarksIn the petroleum industry, multiphase flow is a common occurence in production of oil and gas. Two-phase flow of oil and water is commonly encountered in wellbores; however, its hydro-dynamic behavior under a wide range of flow conditions and inclination angles constitutes a relevant unresolved issue for the oil industry.Multiphase flows are characterized by the existence of diverse flow configurations or flow patterns, which can usually be identified by a typical geometrical arrangement of the phases in the pipe. Inherent to each flow pattern are a characteristic spatial distribution of the interface, flow mechanisms, and distinctive values for design parameters such as pressure gradient, holdup, and heat transfer coefficient. There is clear evidence that accurate knowledge of the oil-water flow patterns, their ranges of existence as a function of flow rates and pipe inclination angles, are crucial in predicting many hydrodynamic parameters. These include pressure gradient and holdup in a number of production engineering applications, such as production optimization, optimum string selection, production logging interpretation, downhole metering, and artificial lift design and modeling.A fundamental problem in production engineering is to determine the actual volumetric flow rates of each of the phases flowing at any location in the wellbore. This in...
Calvin Kessler*+ and Gary Frisch*+ Abstract A new-generation, production logging toolstring is being introduced with a sensor that can measure fullbore gas holdup. Unlike previous center-sampling holdup sensors (whether radioactive fluid-density or capacitance holdup), this new sensor responds to the entire cross-sectional area of the production tubulars (casing, tubing, or slotted liner) occupied by gas and liquid. From this response, the holdup fractions for liquid and gas (Yl and Yg) can be determined. The fullbore measurement eliminates previous uncertainties in holdup fractions that can occur when flowing conditions are nonuniform or when water cut is high. This new capability is shown by flow loop comparisons between measurements taken with the fullbore gas-holdup tool and those taken with previous center-sampling holdup sensors in horizontal stratified flowing conditions. The new production logging toolstring includes a high-speed, bidirectional, monocable digital telemetry system. This system permits simultaneous logging with additional tools such as pulsed neutron tools, oxygen-activation water-flow tools, or other radioactive fluid-velocity tools. The combination of production logging sensors with oxygen activation measurements are important for the evaluation in complex well completions where there are flow paths both inside and outside of the production tubulars, such as with slotted liners. An interactive wellsite production logging analysis package has been developed to utilize the improved data. Both flow-loop-based and conventional slip- velocity interpretation methods are available for determining the flow rates of the individual phases. A new method for determining the downhole flow regime is presented which utilizes both the center- sample holdup and the fullbore holdup measurements. Introduction Production logging (PL) data are used to determine the rate and type of fluid entering or leaving the completion string. The production logging data can be classified according to the type of measurement used to obtain the data: fluid velocity, holdup, pressure, temperature, and auxiliary measurements, such as noise. P. 431
scite is a Brooklyn-based organization that helps researchers better discover and understand research articles through Smart Citations–citations that display the context of the citation and describe whether the article provides supporting or contrasting evidence. scite is used by students and researchers from around the world and is funded in part by the National Science Foundation and the National Institute on Drug Abuse of the National Institutes of Health.
customersupport@researchsolutions.com
10624 S. Eastern Ave., Ste. A-614
Henderson, NV 89052, USA
This site is protected by reCAPTCHA and the Google Privacy Policy and Terms of Service apply.
Copyright © 2024 scite LLC. All rights reserved.
Made with 💙 for researchers
Part of the Research Solutions Family.