Optical Fiber Sensors for High-Temperature Monitoring: A Review

Ma, Shaonian; Xu, Yingke; Pang, Yuxi; Zhao, Xian; Li, Yongfu; Qin, Zhenquan; Liu, Zhaojun; Lu, Ping; Bao, Xiaoyi

doi:10.3390/s22155722

Cited by 55 publications

(20 citation statements)

References 204 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Based on the measurements carried out with an OSA presented in Figure 5, an effective operational spectral range of an interrogator is equal to circa 10 nm. Based on Equations ( 2) and ( 4) and parameters from Figure 3, for such a wavelength span, the temperature can be measured in the range of up to 760 • C. However, for some applications, such as power plant monitoring [53,54], or turbine engine examination [18,55,56], a much larger temperature range is required. To overcome such a limitation, one can either use two or more VCSELs in the interrogator unit or extend wavelength sweeping range through either a temperature or current manipulation.…”

Section: Bypassing Limitations Of Optical Interrogatormentioning

confidence: 99%

“…However, with the utilization of specialized optical fiber Bragg gratings, such as sapphire-based (SFBG) ones, much higher temperatures can be measured, reaching up to 2000 degrees Celsius [63][64][65][66]. Such gratings are suitable for applications for which the possibility of measuring high temperatures is essential [19,53]. However, sapphire-based FBGs have a stronger Bragg wavelength and temperature dependence than standard fibers, and thus the value of α = 0.023 nm…”

Section: System Enhancementmentioning

confidence: 99%

See 1 more Smart Citation

High Temperature Measurement with Low Cost, VCSEL-Based, Interrogation System Using Femtosecond Bragg Gratings

Markowski

Bojarczuk

Araszkiewicz

et al. 2022

Sensors

View full text Add to dashboard Cite

In this article, a cost-effective and fast interrogating system for wide temperature measurement with Fiber Bragg Gratings is presented. The system consists of a Vertical Cavity Surface Emitting Laser (VCSEL) with a High Contrast Grating (HCG)-based cavity that allows for the fast tuning of the output wavelength. The work focuses on methods of bypassing the limitations of the used VCSEL laser, especially its relatively narrow tuning range. Moreover, an error analysis is provided by means of the VCSEL temperature instability and its influence on the system performance. A simple proof of concept of the measurement system is shown, where two femtosecond Bragg gratings were used to measure temperature in the range of 25 to 800 °C. In addition, an exemplary simulation of a system with sapphire Bragg gratings is provided, where we propose multiplexation in the wavelength and reflectance domains. The presented concept can be further used to measure a wide range of temperatures with scanning frequencies up to hundreds of kHz.

show abstract

Section: Bypassing Limitations Of Optical Interrogatormentioning

confidence: 99%

Section: System Enhancementmentioning

confidence: 99%

High Temperature Measurement with Low Cost, VCSEL-Based, Interrogation System Using Femtosecond Bragg Gratings

Markowski

Bojarczuk

Araszkiewicz

et al. 2022

Sensors

View full text Add to dashboard Cite

show abstract

“…Interferometer-based high temperature sensors are usually realized by fabricating micro-cavity structures using laser writing, mode field mismatch by mismatch fusion splicing, fiber tapers by electric arc discharge or oxyhydrogen flame, and so on. According to the different interference structures, high-temperature fiber-optic sensors can be divided into several types, including transmission type, such as Mach-Zehnder interferometers (MZIs), and reflection type, such as Michelson interferometer (MIs), and Fabry–Perot interferometers (FPIs) [ 10 , 11 ]. Most interferometric high temperature fiber-optic sensors can operate with higher temperature sensitivity (10–165 pm/°C) compared with FBG sensors thanks to the higher sensitivity of the optical phase difference (OPD) on temperature variations [ 10 ].…”

Section: Introductionmentioning

confidence: 99%

“…According to the different interference structures, high-temperature fiber-optic sensors can be divided into several types, including transmission type, such as Mach-Zehnder interferometers (MZIs), and reflection type, such as Michelson interferometer (MIs), and Fabry–Perot interferometers (FPIs) [ 10 , 11 ]. Most interferometric high temperature fiber-optic sensors can operate with higher temperature sensitivity (10–165 pm/°C) compared with FBG sensors thanks to the higher sensitivity of the optical phase difference (OPD) on temperature variations [ 10 ]. Unfortunately, the use of laser inscriptions or the precision fabrication of microstructures unavoidably increases the complexity of sensor preparation and cost, and reduces the mechanical strength of the sensors.…”

Section: Introductionmentioning

confidence: 99%

High-Temperature Sensing Based on GAWBS In Silica Single-Mode Fiber

Pang

et al. 2023

Sensors

Self Cite

View full text Add to dashboard Cite

High temperature detection is a constant challenge for condition monitoring under harsh environments in optical fiber sensors research. In this study, the temperature response characteristics of guided acoustic wave Brillouin scattering (GAWBS) spectra in silica single-mode fiber (SMF) up to 800 °C are experimentally investigated, demonstrating the feasibility of the method for high-temperature monitoring. With increasing temperature, the resonance frequency of GAWBS spectra increases in a nearly linear manner, with linearly fitted temperature-dependent frequency shift coefficients of 8.19 kHz/°C for TR2,7 mode and 16.74 kHz/°C for R0,4 mode. More importantly, the linewidth of the GAWBS spectra is observed to narrow down with increasing temperature with a linearly fitted rate of −6.91 × 10−4/°C for TR2,7 modes and −8.56 × 10−4/°C for R0,4 modes. The signal-to-noise ratio of the GAWBS spectra induced by both modes increase by more than 3 dB when the temperature rises from 22 °C to 800 °C, which indicates that the proposed sensing scheme has better performance in high-temperature environments, and are particularly suitable for sensing applications in extreme environments. This study confirms the potential of high-temperature sensing using only GAWBS in silica fibers without any complex micromachining process, which has the advantages of strong mechanical strength, simple structure, easy operation, and low cost.

show abstract

“…The reliable temperature monitoring plays a key role in the metallurgical industry, aerospace field, nuclear energy production, and medical applications [1,2]. In the metallurgical industry, a real-time monitoring of the internal temperature of high-temperature boilers is keys to measure combustion efficiency and the safety prevention [3,4].…”

Section: Introductionmentioning

confidence: 99%

Optical Fiber Based Temperature Sensors: A Review

Gangwar¹,

Kumari²,

Pathak³

et al. 2023

Preprint

View full text Add to dashboard Cite

Current generation witnesses a huge interest in optical waveguide due to their salient feature such as low cost, immune to electromagnetic interference, easy to multiplex, compact size, etc. These features of the optical fibers makes it an useful tool for various sensing applications including medicine, automotive, biotechnology, food quality control, aerospace, physical and chemical monitoring etc. Among all the reported application, the device has been widely exploited to measure the physical and chemical variation in surrounding environment. Optical fiber based temperature sensor plays a crucial role in this decade to detect high fever and tackle COVID like pandemic. Recognizing the major developments in the field of the optical fibers, this article aims to provide recent progress in temperature sensor utilizing several sensing configuration including standard fiber, photonic crystal fiber, and Bragg grating fibers. Additionally, the article also highlights the advantages, limitations, and future possibilities in this area.

show abstract

Optical Fiber Sensors for High-Temperature Monitoring: A Review

Cited by 55 publications

References 204 publications

High Temperature Measurement with Low Cost, VCSEL-Based, Interrogation System Using Femtosecond Bragg Gratings

High Temperature Measurement with Low Cost, VCSEL-Based, Interrogation System Using Femtosecond Bragg Gratings

High-Temperature Sensing Based on GAWBS In Silica Single-Mode Fiber

Optical Fiber Based Temperature Sensors: A Review

Contact Info

Product

Resources

About