Optimization and Elimination of Bottlenecks in the Production Process of a Selected Company

Trebuňa, Peter; Kliment, Marek; Fiľo, Milan

doi:10.4028/www.scientific.net/amm.611.370

Cited by 5 publications

(5 citation statements)

References 7 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Then electric vehicles can enter to the European and world market. European car manufacturers associated in ACEA organizations intend to install these standards to the vehicles from 2017 [10,23,24]. Generally accepted standards have reduced costs for energy companies and the automotive industry.…”

Section: The Standardization Of Connectorsmentioning

confidence: 99%

Possibilities and Limitations of Electromobiles Utilization

Straka

Chovan

Bindzár

et al. 2014

AMM

View full text Add to dashboard Cite

The article is focused on the actual issues of possibilities of charging stations constructions for utilization of electromobiles. Whereas the development of the area in question is dependent on possibility to fill up the energy that drives the vehicle, it is important to determine the allocation and layout of charging points. In terms of satisfying the initial requirements of electromobilists is important opportunity to recharge an electric vehicle in places that are frequently visited and where we spend some time which is sufficient for the charging of electomobile. The current state of construction charging stations within specific sites and the Slovak Republic as such is dependent on finance, legislation, landowners, the quantity of electric cars on the market and resolution to go to these projects. Within the article is nearer remitted to the possibilities and limitations that affect locality selection and construction of charging stations for electric cars needs in Slovakia.

show abstract

Section: The Standardization Of Connectorsmentioning

confidence: 99%

Possibilities and Limitations of Electromobiles Utilization

Straka

Chovan

Bindzár

et al. 2014

AMM

View full text Add to dashboard Cite

show abstract

“…For this reasons it is necessary to design new approach for solution of layout of distribution spaceelements, in the way to considerate not only cost side of solution but also criteria, which are not possible immediately to express mathematically, but have permanent impact for costs [21,22,23]. It is also an advantage, that this solution is graphically displayed, so a researcher immediately knows, where it is necessary to allocate required places and how total layout of defined positionslooks like.…”

Section: New Approach To the Layout Of Distribution System Elementsmentioning

confidence: 99%

New Method for Design of Transport Infrastructure Elements

Straka

Balog

Bindzár

et al. 2014

AMM

View full text Add to dashboard Cite

A trend in automotive freight has experienced rapid development in recent years. The increase of traffic intensities is closely related to the increasing demand of building elements of transport the infrastructure that will provide services to monitor traffic, inform road users and protect transport companies property and citizens who participate in the process of transportation. The current state of layout and allocation problem solving of elements of transport infrastructure is limited to the use of mathematical, multicriteria or heuristic methods. Each approach has its advantages and limitations but none of them solves same layout and allocation of a particular procedure with a specific position. System of blocks (SB) method is a method, which joints the layout and allocation into one unit, using the principles of mathematics, multicriteria, heuristic procedures and graphics simultaneously. The advantage of the proposed method is the complexity of the proposed solution, i.e. consideration of multi-criteria approach with no pre-defined positions and precise definition and the actual position of the elements in space allocation.

show abstract

“…Prefabrication construction is an important part of building industrialization. It is mainly transformed from site construction to field assembly by decomposing building production cycle, improves product quality, promotes staff enthusiasm and improves production efficiency (Trebuna et al, 2014).…”

Section: Introductionmentioning

confidence: 99%

Research on production process optimization of precast concrete component factory based on value stream mapping

Wang

Tang

Zou

et al. 2019

ECAM

View full text Add to dashboard Cite

Purpose The purpose of this paper is to investigate the process optimization of a precast concrete component production line by using value stream mapping. Design/methodology/approach This paper is an empirical focused on of lean production theory and value stream mapping. The data in the case study were collected in real time on-site for each process during the production process of a prefabricated exterior wall. Findings The results of the current value stream map indicate that the main problems of the current production process are related to equipment, technology and organization. The equipment problems include simple demolding and cleaning tools and the lack of professional transfer channels. The technology problems include the lack of a marking mechanism and pipeline exit mechanism. There is a lack of standard operating procedures and incomplete process convergence. A comparison and analysis of the current value stream and the future value flow indicate that optimizations of the process flow, the production line layout, and the standard operating procedures have shortened the delivery cycle, reduced the number of workers, improved the operator’s operating level and balanced the production line. Practical implications The results of this study provide practitioners with a clear understanding of the optimization of the precast concrete component production and represent a method and basis for the process optimization of a factory production line; the approach is suitable for process optimization in other areas. Originality/value This research represents an innovative application of lean production theory and value stream mapping in a complex production line of precast concrete components and thereby fills the gap between the theory and practice of the optimization of a precast concrete component production line.

show abstract

Optimization and Elimination of Bottlenecks in the Production Process of a Selected Company

Cited by 5 publications

References 7 publications

Possibilities and Limitations of Electromobiles Utilization

Possibilities and Limitations of Electromobiles Utilization

New Method for Design of Transport Infrastructure Elements

Research on production process optimization of precast concrete component factory based on value stream mapping

Contact Info

Product

Resources

About