Powder Metallurgy Production of Ti–5.4 wt.% Si Alloy. I. Simulating the Formation of Powder Particles by Centrifugal Atomization

Brodnikovskii, D. N.; Lugovoi, N. I.; Brodnikovskii, N. P.; Slyunyaev, V. N.; Кulak, L. D.; Vasil’ev, A. D.; Фирстов, С. А.

doi:10.1007/s11106-013-9541-7

Cited by 9 publications

(3 citation statements)

References 6 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Of course, the main role in the properties of a nanomaterial is played by the type of system, which can be single-component [74][75] or multicomponent [76][77][78][79]. No less important is the technology of preparation [80][81][82][83][84][85] and processing of the material before its use, which confirms the theoretical [90][91][92] and experimental [93][94][95][96][97][98][99][100] data.…”

Section: Introductionsupporting

confidence: 60%

Crystalline potassium dihydrogen phosphate (KDP) powders

Zolotarenko,

Matysina

et al. 2023

Poverhn.

View full text Add to dashboard Cite

The article discusses the use of KDP ferroelectric crystals (phosphates and arsenates of potassium, rubidium, cesium) and their deuterated analogues in various industries, including the creation of electro-optical devices and as hydrogen sorbents. The paper describes the physical properties of KDP crystals, changes in their properties near the phase transition temperature, as well as methods for obtaining KDP nanocrystals and their application in biomedicine. The paper also states that the phase transition in KDP crystals occurs near room temperature and manifests itself in a change in their physical properties, such as dielectric constant, optical properties, and heat capacity. In addition, approaching the phase transition temperature causes a change in the crystal lattice parameters, which can lead to the appearance of anomalous effects. The structure of the unit cell of potassium dihydrogen phosphate (KH2PO4) is considered. The plots of the temperature dependence of the order parameter of spontaneous polarization and the plots of the temperature dependence of the configurational heat capacity of the crystal in the phase transition region are calculated, and the plots of the temperature of the inverse and direct dielectric susceptibility are calculated. Graphs of the order parameter, which characterizes the degree of spontaneous polarization for different temperatures, depending on the strength of the external electric field, are also calculated.

show abstract

Section: Introductionsupporting

confidence: 60%

Crystalline potassium dihydrogen phosphate (KDP) powders

Zolotarenko,

Matysina

et al. 2023

Poverhn.

View full text Add to dashboard Cite

show abstract

“…In recent years, PREP has become the hot research topics in the titanium alloy powder preparation 17,18) .The quality and properties of the powders are determined by the experimental parameters including the melting rate, billet diameter, rotating speed, and plasma gas composition. These parameters are interrelated by the following equation 19) .…”

Section: The Relationship Between Rotating Speed and Particle Size Cmentioning

confidence: 99%

Microstructure and Properties of High Temperature Titanium Alloys with a High Si Content Prepared by Powder Metallurgy

Kuang

Zou²,

Cai³

et al. 2017

Mater. Trans.

View full text Add to dashboard Cite

The objective of this paper is to improve the performance of high temperature titanium alloys with a high Si content by powder metallurgy. Firstly Ti-6.5Al-1.4Si-2Zr-0.5Mo-2Sn alloy powders were prepared using two different rotating speeds by plasma rotating electrode process (PREP). Then two sintering temperatures were selected to fabricate titanium alloys by hot isostatic pressing (HIP). The relationship between rotating speed and particle size distribution was investigated. X-ray diffraction, SEM, and OM were used to characterize the phase compositions, morphologies, and microstructures of the powders and titanium alloys. The mechanical properties of titanium alloys were investigated at room temperature,300 C and 600 C. The results show that high quality titanium alloy powders were prepared by PREP. The mechanical properties of titanium alloy fabricated by powder metallurgy were superior compared to casting.And the strength is higher than typical Ti-1100 high temperature alloy. [

show abstract

“…The type of systems of such materials (single-component [73][74] or multicomponent [75][76][77][78] systems) plays an important role, as does the preparation [79][80][81][82][83][84] and processing [85][86][87][88] of metals, what is confirmed by experimental [89][90][91][92][93][94][95][96] and theoretical data [97][98][99].…”

Section: Introductionmentioning

confidence: 99%

Creation of 3D-products using carbon nanostructures and 3D-printing technologies (FDM, CJP, SLA, SLS)

Zolotarenko,

Rudakova

et al. 2023

Poverhn.

View full text Add to dashboard Cite

The article discusses methods for obtaining carbon nanostructures (CNS), as well as their use to create three-dimensional (3D) products using FDM, CJP, SLA, SLS technologies. The process of manufacturing consumables for 3D printing technologies (FDM, CJP, SLA, SLS) for creating new composite 3D products based on carbon nanostructures is described. The paper contains a detailed description of which methods of CNS synthesis are more productive and how they allow you to guarantee the production of one or another type of CNS. The paper analyzes the existing 3D printing technologies using CNS, developed a scheme for the full cycle of creating a 3D product containing CNS, taking into account various methods for the synthesis of CNS with the transformation of graphite or other carbon-containing material. It also describes the process of creating composite coils for FDM 3D printing from nanocomposite filaments (rigid polymer-CNS) based on a rigid polymer, which have undergone the process of preparation in a special mixer. The process of preparing consumables and printing a 3D volumetric product using FDM, CJP, SLA, SLS technologies using CNS is described. An overview of consumables for 3D products of FDM technology is presented. The analysis of composite 3D products (ceramic-CNS, rigid polymer-CNS) obtained by FDM and CJP technology was carried out. The paper also describes the three most productive methods for the synthesis of CNS: plasma-chemical synthesis in gas or liquid and pyrolytic method. These synthesis methods make it possible to guarantee the production of a certain type of CNS and have a high quality of the obtained nanoproducts. Various types of CNS are described, including soluble (fullerenes and fullerene-like structures) and insoluble nanostructures (graphenes, carbon nanotubes, carbon nanofibers, nanocomposites, etc.).

show abstract

Powder Metallurgy Production of Ti–5.4 wt.% Si Alloy. I. Simulating the Formation of Powder Particles by Centrifugal Atomization

Cited by 9 publications

References 6 publications

Crystalline potassium dihydrogen phosphate (KDP) powders

Crystalline potassium dihydrogen phosphate (KDP) powders

Microstructure and Properties of High Temperature Titanium Alloys with a High Si Content Prepared by Powder Metallurgy

Creation of 3D-products using carbon nanostructures and 3D-printing technologies (FDM, CJP, SLA, SLS)

Contact Info

Product

Resources

About