Preparation and characterization of the plasticized polylactic acid films produced by the solvent‐casting method for food packaging applications

Abstract

A strategy to overcome the brittleness and rigidity of polylactic acid (PLA)-based materials for food packaging applications is adding a proper plasticizer in the right amount. Here, triacetin (TA) and polyethylene glycol (PEG) were used as plasticizers in different amounts (10, 20, and 30 wt%) to produce the plasticized PLA films by the solvent-casting method. Tensile properties, water vapor permeability (WVP), moisture content (MC), optical properties, Fourier transform infrared absorption (FTIR), and thermogravimetric analysis (TGA) are reported. The results showed that both TA and PEG cause increasing elongation at break (E ab ) and decreasing tensile strength (TS), where the plasticized PLA films containing 10 and 30 wt% of TA showed the highest TS (26.6 MPa) and E ab (81.1%), respectively. Light transmission of PLA was decreased by introducing the plasticizers, while WVP, MC, and opacity of the plasticized films were increased compared to the neat PLA. Among the plasticized films, the sample with 10 wt% of TA and PEG showed the lowest WVP (4.9 × 10 −10 g/m s −1 Pa −1 ) and MC (5.5%), respectively. Based on the TGA, an improvement in the thermal stability of TA and PEG plasticized films compared to the neat PLA was obvious. The sample containing 10 wt% of TA (PLA-TA10) showed the best performance for food packaging applications. Practical applicationsFood product packaging provides retarding deterioration, reducing microbial contamination, preserving safety, protecting quality, and extending the shelf life of packaged foods during transmission, storage, and consumption. Petroleum-based plastic and synthetic polymers have been mainly used in food packaging due to their cheap cost and good mechanical and barrier properties. However, increasing the use of these nonbiodegradable polymers causes serious environmental and health problems. The biopolymers which are extracted from biodegradable and renewable sources are considered as suitable alternatives for petroleum-based plastic materials.However, application of biopolymers as packaging materials has been limited due to their low mechanical properties and thermal stability. Many studies have been conducted to modify the properties of PLA-based packaging materials to create a favorable product for the food industry. Moreover, introducing plasticizer to PLA helps

Characterization of biodegradable food packaging films prepared with polyamide 4: Influence of molecular weight and environmental humidity

“…While the transmittance at 660 nm for PA4‐1, PA4‐2, PA4‐3, and PA4‐4 were 51.7%, 53.7%, 55.8%, and 59.9%, respectively. Compared with the reported PLA films ( T 280 = 8.4%, T 660 = 38.6%), PA4 exhibited a higher UV light barrier and better transparency (YousefniaPasha et al, 2021). It was also found that the light transmission of PA4 increased with increasing molecular weight, although these differences were almost negligible on the macroscopic scale.…”

“…The ingredients in packaged food are vulnerable to degradation, nutrient loss, discoloration, odor creation, and other spoilage reactions when exposed to UV or visible light (YousefniaPasha et al, 2021). Therefore, it is vital to characterize the optical characteristics of packaging materials.…”

Thermal and mechanical properties of aminolyzed‐poly(lactic acid) with amine‐terminated dendritic polymer: Surface and bulk functionalization

“…Generally, PLA properties can be tailored through bulk or surface modifications. The first one employs techniques such as blending, 12,13 solvent casting, 14,15 copolymerization, 16,17 and cross‐linking 18,19 . For example, Raj et al 20 successfully enhanced the thermomechanical properties of poly( l ‐lactic acid) through blending with 30 wt% of polyamide12 in which the final product showed maximal ductility of 225%, impact toughness of 48 kJ m −2 , and thermal resistance up to 123°C.…”

“…Generally, PLA properties can be tailored through bulk or surface modifications. The first one employs techniques such as blending, 12,13 solvent casting, 14,15 copolymerization, 16,17 and cross-linking. 18,19 For example, Raj et al 20 successfully enhanced the thermomechanical properties of poly(L-lactic acid) through blending with 30 wt% of polyamide12 in which the final product showed maximal ductility of 225%, impact toughness of 48 kJ m À2 , and thermal resistance up to 123 C. Another approach of surface modification includes techniques that may influence the surface properties through chemical and/or physical treatment such as alkaline hydrolysis, plasma treatment, enzyme modification, coating, 21 and aminolysis.…”

Porous Fe-Porphyrin as an Efficient Adsorbent for the Removal of Ciprofloxacin from Water

“…There is an increasing focus on minimizing environmental impact, advancing sustainability, and promoting the well-being of both current and future generations . Scientists are exploring diverse approaches to address global challenges related to sustainability. , In recent decades, escalating water pollution, driven by population growth and human activities, has emerged as a major concern for human health. The release of hazardous pollutants into water systems is linked to issues such as bacterial resistance and a rise in hormonal and genetic diseases .…”