Preparation of ITO Nanoparticles by Liquid Phase Coprecipitation Method

Ding, Zhiying; An, Cunran; Li, Qiang; Hou, Zhenshan; Wang, Jianqiang; Qi, Haibo; Qi, Fangjuan

doi:10.1155/2010/543601

Cited by 17 publications

(6 citation statements)

References 15 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Moreover, the sizes of the ITO nanospheres can be readily controlled by variation of the thicknesses of the ITO films. Ding et al 15 synthesized nanoscale ITO particles with a distribution of particle size of 30-90 nm by liquid-phase coprecipitation method under given conditions with solutions of indium chloride, tin chloride, ammonia, and two kinds of surfactants as dispersants. In the consideration of a fast and inexpensive fabrication method, the wet-chemical deposition of ITO nanoparticles as an alternating approach should be preferred.…”

Section: CLmentioning

confidence: 99%

Fabrication and properties of nano indium tin oxide/wool keratin composites

Wen

et al. 2013

J of Applied Polymer Sci

View full text Add to dashboard Cite

A functional keratin/indium tin oxide (ITO) composite was prepared by a route involving an ionic liquid dissolving process and a wet-chemical codeposition technique. The crystal structure and morphology of ITO were investigated by X-ray diffraction and transmission electron microscopy, respectively. The factors influencing the crystal structure and the size of the ITO were investigated in detail. The optimal In/Sn ratio, reaction temperature, and pH value were found to be 10:1, 70 C, and 7, respectively. The sheet resistance of the composite reached 0.39 kX/ w . In addition, the composite films possessed a perfect UV protection ability with a UV protection factor of up to 43.78.

show abstract

Section: CLmentioning

confidence: 99%

Fabrication and properties of nano indium tin oxide/wool keratin composites

Wen

et al. 2013

J of Applied Polymer Sci

View full text Add to dashboard Cite

show abstract

“…Salah satunya lapis tipis ITO (Indium Tin Oxide), merupakan lapisan tipis yang memiliki sifat transparansi tinggi pada daerah sinar tampak dengan nilai band gap lebih besar dari 3,5 eV dan hambatan listrik yang rendah (Ding et al, 2010). Lapisan tipis ITO berperan penting dalam bidang teknologi saat ini diantaranya pada sel surya, Liquid Crystal Display (LCD), Light Emitting Diodes (LED), optoelektronik, sensor gas dan lain-lain.…”

Section: Pendahuluanunclassified

Pengaruh DEA dan Waktu Dipping terhadap Nilai Band Gap Lapisan Tipis CuSnO3

Rizka,

Sanjaya

2023

masaliq

View full text Add to dashboard Cite

CuSnO3 is one of the semiconductor materials that can be used in the manufacture of thin film. CuSnO3 is an amorphous semiconductor with a band gap of 2.0-2.5 eV. Dip-coating is one method that can be used to synthesize a thin film of CuSnO3. This study aims to see the effect of DEA additives and dipping time on the band gap value of a thin film of CuSnO3. The results of a thin film of CuSnO3 using the dip-coating method with DEA variations of 1 ml, 1.5 ml, and 2 ml as additives, obtained band gap values of 2.55 eV, 2.41 eV, and 2.31 eV. The larger the volume of DEA, the smaller the band gap value produced. At dipping times of 10 minutes, 15 minutes, and 20 minutes, band gap values of 2.58 eV, 2.31 eV, and 2.26 eV were recorded. The longer the time it takes to dye, the smaller the band gap value produced.

show abstract

“…Hydrothermal method on the other hand requires high reaction temperature and pressure yielding homogeneous, uniform & large sized and quality crystalline nanomaterials [27][28][29][30]. Sol-gel method is a self-propagating low temperature ignition process that produces fine and homogeneous nanomaterials.…”

Section: Introductionmentioning

confidence: 99%

ITO Conductive Ink: Advances in Materials, Preparation, and Potential Sensor Applications

Hiroli

Manjunatha

2022

ECS Trans.

View full text Add to dashboard Cite

The global conductive ink market size has been expected around a CAGR of 4.1%, by value and the market is estimated to be USD 3.0 to 3.7 billion in 2020-2025. Indium tin oxide (ITO) ink is used as conducting ink and in engineering applications. Therefore, the review is aimed to provide more insights into various reactants precursors, conditions, and synthesis procedure for the development of ITO nano inks. The merits and demerits of the various methods such as hydrothermal, solvothermal, spray pyrolysis, sol-gel, and electrophoretic deposition, magnetron sputtering etc., used for making ITO nanoparticles were discussed in detail. Further, various ink properties, parameters, and processes for development of ITO nano ink proposed by different research groups is also discussed. The suitable conditions to print the prepared ITO ink on suitable substrate using ink-jet fabrication methodology discussed by various research groups is also explored. Also, the review focusses on the study of the properties of the printed ink such as transmittance and the sheet resistance are also studied. Finally, the sensitivity, response, and recovery of the ITO coated electrode developed for various sensor applications is discussed in detail.

show abstract

Preparation of ITO Nanoparticles by Liquid Phase Coprecipitation Method

Cited by 17 publications

References 15 publications

Fabrication and properties of nano indium tin oxide/wool keratin composites

Fabrication and properties of nano indium tin oxide/wool keratin composites

Pengaruh DEA dan Waktu Dipping terhadap Nilai Band Gap Lapisan Tipis CuSnO3

ITO Conductive Ink: Advances in Materials, Preparation, and Potential Sensor Applications

Contact Info

Product

Resources

About