Processing of Al–12Si–TNM composites by selective laser melting and evaluation of compressive and wear properties

Prashanth, K.G.; Scudino, Sergio; Chaubey, Anil Kumar; Löber, Lukas; Wang, Pei; Attar, Hooyar; Schimansky, F.P.; Pyczak, Florian; Eckert, J.

doi:10.1557/jmr.2015.326

Cited by 112 publications

(30 citation statements)

References 57 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The wear track of the sample observed by SEM is shown in Figure 7. The wear track of the sample (Figure 7) shows the presence of wear scars along the sliding direction typical for a wear surface and the presence of ploughing grooves and delamination at certain regions similar to that reported in References [39][40][41][42]. The process of coating wear was accompanied by cracking of the coating.…”

Section: Resultssupporting

confidence: 68%

Zircon-Based Ceramic Coatings Formed by a New Multi-Chamber Gas-Dynamic Accelerator

et al. 2017

View full text Add to dashboard Cite

Abstract:In this work, dense zircon-based ceramic coatings were obtained from inexpensive zircon powder on a steel substrate by using a new multi-chamber gas-dynamic accelerator. The microstructure and phase composition of the coating were characterized by scanning electron microscopy, optical microscopy, and X-ray diffraction. The mechanical properties of the coatings were evaluated using microindentation, wear tests and bonding strength tests. The results showed that the obtained zircon-based ceramic coatings were continuous without cracks and bonded well with substrate without a sublayer. The zircon-based ceramic coatings consisted of c-ZrO 2 (major phase), m-ZrO 2 and SiO 2 . The zircon-based ceramic coatings had a porosity of 0.1%, hardness of 526 ± 65 HV 0.2 , and a fracture toughness of 2.5 ± 0.6 (MPa·m 1/2 ). The coatings showed the low specific wear rate and average erosion rate. The failure mode occurring in the tested coatings was cohesive.

show abstract

Section: Resultssupporting

confidence: 68%

Zircon-Based Ceramic Coatings Formed by a New Multi-Chamber Gas-Dynamic Accelerator

et al. 2017

View full text Add to dashboard Cite

show abstract

“…The wear tracks of the composites show the presence of typical wear features including wear scars, ploughing grooves, and delamination. The composites with (80-100 µm) particle size show shallow ploughing grooves along with the presence of some delamination cracks (Figure 4a), which are formed at the surface of the sample in contact with the counter disc due to high strain levels developed during the wear test [33][34][35]. The samples of 40-80 µm particles size (seen in Figure 4b) also show a similar nature of wear surface but ploughing groves are not clearly visible.…”

Section: Resultsmentioning

confidence: 95%

Effect of Particle Size on Microstructure and Mechanical Properties of Al-Based Composite Reinforced with 10 Vol.% Mechanically Alloyed Mg-7.4%Al Particles

et al. 2016

Self Cite

View full text Add to dashboard Cite

Abstract:The effect of Mg-7.4%Al reinforcement particle size on the microstructure and mechanical properties in pure Al matrix composites was investigated. The samples were prepared by hot consolidation using 10 vol.% reinforcement in different size ranges, D, 0 < D < 20 µm (0-20 µm), 20 ≤ D < 40 µm (20-40 µm), 40 ≤ D < 80 µm (40-80 µm) and 80 ≤ D < 100 µm (80-100 µm). The result reveals that particle size has a strong influence on the yield strength, ultimate tensile strength and percentage elongation. As the particle size decreases from 80 ≤ D < 100 µm to 0 < D < 20 µm, both tensile strength and ductility increases from 195 MPa to 295 MPa and 3% to 4% respectively, due to the reduced ligament size and particle fracturing. Wear test results also corroborate the size effect, where accelerated wear is observed in the composite samples reinforced with coarse particles.

show abstract

“…where W a is the abrasion wear rate (mm 3 /Nm), ∆G is mass loss (g), d is density (g/mm 3 ), M is the applied load (N), and S is the sliding distance (m) [39,40].…”

Section: Methodsmentioning

confidence: 99%

Mechanical and Tribological Properties of Al2O3-TiC Composite Fabricated by Spark Plasma Sintering Process with Metallic (Ni, Nb) Binders

Kumar

Chaubey

Maity

et al. 2018

Metals

View full text Add to dashboard Cite

Al 2 O 3 -10TiC composites were fabricated through the powder metallurgical process (mechanical milling combined with spark plasma sintering) with the addition of Ni/Nb as metallic binders. The effect of binder addition (Ni/Nb) on the processing, microstructure, and mechanical and tribological properties of the bulk-sintered composite samples was investigated. The microstructure of the composite reveals a homogeneous distribution of the TiC particles in the Al 2 O 3 matrix. However, the presence of Ni/Nb was not traceable, owing to the small amounts of Ni/Nb addition. Hardness and density of the composite samples increase with the increasing addition of Nb (up to 2 wt. % Nb). Any further increase in the Nb content (3 wt. %) decreases both the hardness and the wear resistance. However, in case of Ni as binder, both the hardness and wear resistance increases with the increase in the Ni content from 1 wt. % to 3 wt. %. However, the composite samples with Nb as binder show improved hardness and wear resistance compared to the composites with Ni as binder.

show abstract

Processing of Al–12Si–TNM composites by selective laser melting and evaluation of compressive and wear properties

Cited by 112 publications

References 57 publications

Zircon-Based Ceramic Coatings Formed by a New Multi-Chamber Gas-Dynamic Accelerator

Zircon-Based Ceramic Coatings Formed by a New Multi-Chamber Gas-Dynamic Accelerator

Effect of Particle Size on Microstructure and Mechanical Properties of Al-Based Composite Reinforced with 10 Vol.% Mechanically Alloyed Mg-7.4%Al Particles

Mechanical and Tribological Properties of Al2O3-TiC Composite Fabricated by Spark Plasma Sintering Process with Metallic (Ni, Nb) Binders

Contact Info

Product

Resources

About