Proposal for Environmental Vibration Measurement Method on Carpet Using Vibration Control Rubber

Tomita, Ryuta; Goto, Yuta

doi:10.3130/aije.84.635

Cited by 6 publications

(4 citation statements)

References 0 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The experimental patterns for the method of estimation using the vibration transmission rate of vibration control rubber proposed in this study are the same as those of the above experimental method. The theory has been presented in previous papers [2], etc.…”

Section: Results and Discussion Of Experiments Using Vibration Transm...mentioning

confidence: 99%

“…Next, experiments `, ˆ, and ˜in Table 2 were performed to carry out the method of estimation using the vibration transmission rate of vibration control rubber proposed in this study. This method was proposed in a past paper [2]. In another previous study [3], an experimental study of vertical vibration using a vibration generator based on the method proposed in this study was conducted, and it was shown to be possible to measure vertical vibration with almost no mounted resonance effect.…”

Section: Experimental Methodsmentioning

confidence: 93%

“…The method proposed in this study [2], etc. is aimed at the accurate measurement of the vibration of the floor structure underneath a carpet by using soft vibration control rubber without the need to peel the carpet away.…”

Section: Introductionmentioning

confidence: 99%

“…Low-frequency contact resonance is generated because of the vibration control rubber and the accelerometer and the resulting vibration transmission rate is used. As described in a previous paper [2], using the method proposed in this study, when a carpet is installed on top of concrete slabs, it is possible to accurately measure the vibration of the floor structure underneath the carpet without peeling the carpet away.…”

Section: Introductionmentioning

confidence: 99%

See 3 more Smart Citations

Comparison of vibration transmission rate when using vibration control rubber and DIN 45669-2 method for countermeasures to contact resonances of vertical vibration

Tomita

Goto

Adachi³

2022

Acoust. Sci. & Tech.

Self Cite

View full text Add to dashboard Cite

When an accelerometer is placed on a soft floor covering such as a carpet, a resonance system is created by the spring of the carpet and the mass of the accelerometer, and vibrations are amplified at the resonance frequency. This is called ''contact resonance.'' Therefore, to accurately measure the vibration of the floor structure underneath the carpet, it is generally necessary to first peel off the floor covering. Contact resonances on surfacing materials such as carpets and tatamis must be considered when measuring the vibration of buildings. The German standard is DIN 45669-2. In this report, we present a comparison of the method specified in DIN 45669-2 and a method using vibration control rubber proposed in this study. Measurement results showed that, when using the DIN 45669-2 method, there was almost no contact resonance effect for the thinnest carpet, but for other carpets, a contact resonance effect was observed. The values estimated by the method using the vibration transmission rate of vibration control rubber showed that the contact resonance effect can be reduced for the carpets examined in this study.

show abstract

Section: Results and Discussion Of Experiments Using Vibration Transm...mentioning

confidence: 99%

Section: Experimental Methodsmentioning

confidence: 93%

Section: Introductionmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Comparison of vibration transmission rate when using vibration control rubber and DIN 45669-2 method for countermeasures to contact resonances of vertical vibration

Tomita

Goto

Adachi³

2022

Acoust. Sci. & Tech.

Self Cite

View full text Add to dashboard Cite

show abstract

Study for Error Reduction of Contact Resonances Using Vibration Control Rubber for Vertical and Horizontal Vibration of Tatami on Vibration Generator

TOMITA,

ADACHI

2023

Nihon Kenchiku Gakkai Kankyokei Ronbunshu

View full text Add to dashboard Cite

We have conducted various studies on methods to prevent contact resonances. It was suggested that the proposed method of the previous studies could be used to estimate carpets and building material tatami. On the other hand, there was a problem with the straw tatami.Therefore, in this paper, we conducted an experimental study on an estimation method that is an extension of the proposed method for vertical and horizontal vibration. As a result, it was shown that by considering the proposed modified estimation methods, the error of the contact resonances can be reduced and estimated even with the straw tatami.

show abstract

Examination of Environmental Vibration Measurement Using Vibration Control Rubber for Horizontal Vibration on Tatami

Tomita

Adachi²

2021

AIJ J. Technol. Des.

View full text Add to dashboard Cite

Proposal for Environmental Vibration Measurement Method on Carpet Using Vibration Control Rubber

Cited by 6 publications

References 0 publications

Comparison of vibration transmission rate when using vibration control rubber and DIN 45669-2 method for countermeasures to contact resonances of vertical vibration

Comparison of vibration transmission rate when using vibration control rubber and DIN 45669-2 method for countermeasures to contact resonances of vertical vibration

Study for Error Reduction of Contact Resonances Using Vibration Control Rubber for Vertical and Horizontal Vibration of Tatami on Vibration Generator

Examination of Environmental Vibration Measurement Using Vibration Control Rubber for Horizontal Vibration on Tatami

Contact Info

Product

Resources

About