Rapid prototyping of control systems using embedded target for TI C2000 DSP

Duma, Radu; Dobra, Petru; Abrudean, Mihail; Dobra, Mirela

doi:10.1109/med.2007.4433860

Cited by 22 publications

(8 citation statements)

References 1 publication

Supporting

Mentioning

Contrasting

Order By: Relevance

“…With this setup, the experimental results of the conventional method and the proposed method can be obtained by changing only the DSP program accordingly whilst keeping the system hardware unchanged. Further, for rapid programming, the DSP is coded using the Matlab/Simulink software combining with the Code Composer Studio (CCS) compiler from TI, which is proposed in the previous works [32][33][34]. The programming sequence is conducted in three steps: (1) the model of the control algorithm is built using Matlab/Simulink; (2) the Real-Time Workshop ® in Matlab generates C code file from this model; (3) the C code file is downloaded into the DSP board using the CCS compiler.…”

Section: Evaluate the System Reconfiguration Timementioning

confidence: 99%

A Fast, Decentralized, Self-Aligned Carrier Method for Multicellular Converters

et al. 2020

View full text Add to dashboard Cite

This paper proposes a fast, decentralized method for self-aligning the carriers of a multiphase/multilevel converter operating on the basis of phase-shifted pulse width modulation or level-shifted pulse width modulation. In the proposed method, each cell of the converter synchronizes and updates simultaneously its own carrier angle or carrier level based on the information shared with its neighboring cell, such as its angle/level, its index number, and the total number of activated cells of the converter. Different from the conventional decentralized method (with basic and modified updating rules), which requires some conditions in terms of cell number and initial carrier angles to start up and operate properly, the proposed method can be applied to the system with any number of cells and does not require special conditions of initial carrier angles. Further, while the conventional method needs an iteration process to adjust the inter-carrier phase-shifts and can be applied only to a multiphase converter which uses phase-shifted pulse width modulation, the proposed method offers an accurate and fast alignment of phases (for phase-shifted pulse width modulation) or levels (for level-shifted pulse width modulation) and thus can be applied to both multiphase and multilevel converter types. The simulations and the experimental results are presented in detail to show the validity and the effectiveness of the proposed methods. Further, thorough simulations on multiphase converters with different number of cells also show that the proposed method is much faster than the conventional method in both configuration and reconfiguration processes, especially in case the system has a large number of cells.

show abstract

Section: Evaluate the System Reconfiguration Timementioning

confidence: 99%

A Fast, Decentralized, Self-Aligned Carrier Method for Multicellular Converters

et al. 2020

View full text Add to dashboard Cite

show abstract

“…Thus, any modification in the controller configuration or in its adjustment can be easily tested under simulation. Once the control algorithm has been tuned, it can be transferred to the digital controller using toolboxes that allow directly translating the control algorithm to a particular digital processor [35]. These toolboxes generate optimized C code for DSP / FPGA from plain Simulink diagrams.…”

Section: Integration Of Structural / Functional Representationsmentioning

confidence: 99%

Simulation of Electric Vehicles Combining Structural and Functional Approaches

Silva¹,

Magallán²,

Barrera³

et al. 2014

Journal of Electrical Engineering and Technology

View full text Add to dashboard Cite

-In this paper the construction of a model that represents the behavior of an Electric Vehicle is described. Both the mechanical and the electric traction systems are represented using Multi-Bond Graph structural approach suited to model large scale physical systems. Then the model of the controllers, represented with a functional approach, is included giving rise to an integrated model which exploits the advantages of both approaches. Simulation and experimental results are aimed to illustrate the electromechanical interaction and to validate the proposal.

show abstract

“…This DSP system allows fast fixed-point processing at 150 MHz and can be adapted to all motor drives laboratories thanks to its motor control peripherals i.e. 2 event managers, 16 12-Bit ADC channels with fast conversion rate (80 ns) and up to 56 general purpose I/O (GPIO) [18].…”

Section: B Simulink Real-time Models and Dsp Implementationmentioning

confidence: 99%

“…But in general, these papers describe specific and small size applications such as: active power filter [15], Power Factor Boost Rectifier [16], battery charging system [17], DC motor control [18] and DC/DC buck chopper [19]. This paper presents a set of laboratories for the first semester based on eZdspF2812 rapid prototyping system which is also used for the robot project in the second semester.…”

Section: Introductionmentioning

confidence: 99%

Design of PM Motor Drive Course and DSP Based Robot Traction System Laboratory

Yousfi¹,

Belkouch²,

Ouahman³

et al. 2010

Journal of Power Electronics

View full text Add to dashboard Cite

This paper presents a part of North Africa/Europe collaboration results in education to develop project-oriented courses in power electronics and motor drive field. The course aims to teach Permanent Magnet motor drives close to a real world project of significant size and depth so as to be motivational, namely mobile robot project. Particular skills, student will acquire, are those relative to the detailed design and implementation of PM motor controllers in DSP based rapid prototyping environment. Simulation work is completed using graphical modeling tools in Simulink/Plecs, while real-time implementation is achieved by means of eZdspF2812 board and Simulink/TI C2000 Embedded Target tools. This flexible development environment fit the robot traction system very well and provides exactly the functionality necessary for an efficient PM motor drives teaching as demonstrated by a set of simulation and experiments.

show abstract

Rapid prototyping of control systems using embedded target for TI C2000 DSP

Cited by 22 publications

References 1 publication

A Fast, Decentralized, Self-Aligned Carrier Method for Multicellular Converters

A Fast, Decentralized, Self-Aligned Carrier Method for Multicellular Converters

Simulation of Electric Vehicles Combining Structural and Functional Approaches

Design of PM Motor Drive Course and DSP Based Robot Traction System Laboratory

Contact Info

Product

Resources

About