Research on Safety Assessment for Power Line Design

Ding, Jun; Wang, Yong; Guo, Rui; Jia, Shi Xing; Shen, Yan; Wen, Tao; Jun, Da Qu

doi:10.1088/1757-899x/366/1/012068

Cited by 2 publications

(2 citation statements)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…The observed increase in m-values and softening fraction is reasonable in light of the heightened slip activity of non-basal systems at elevated temperatures. [27][28][29] The results presented in Figure 3c,f demonstrate that the compressive formability of both as-built EBM and SLM specimens increases with temperature. This improvement in formability can be attributed to two main factors: dynamic globularization of α-platelets below the β-transus temperature [30][31][32] and the activation of restoration processes such as dynamic recovery and dynamic recrystallization in the fully β region.…”

Section: Flow Stress Behaviormentioning

confidence: 83%

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy

Roshani,

Abedi,

Saboori

2023

Adv Eng Mater

View full text Add to dashboard Cite

The cold, warm, and hot deformation flow behavior and mechanical properties of the Ti‐6242 alloy produced by selective laser melting (SLM) and electron beam melting (EBM) are compared. Hot compression tests are conducted over a wide temperature range (100–1000 °C) at a constant strain rate of 0.001 s−1. The yield and overall strength levels of the SLMed specimens are higher than those of the EBMed specimens at all temperatures. A thermally stable region is observed for SLMed specimens in the temperature range of 100–700 °C, but the strength level drops significantly (approximately 300–500 MPa) at above 700 °C. The stability region shifts to the lower temperature range of 100–600°Cfor the EBMed specimens, and strength starts to decrease at 600 °C. Both specimens experience fracture in a cold‐temperature regime but exhibit a high strain tolerance of approximately 0.4. The SLMed samples display a completely brittle behavior at a warm temperature regime, whereas, the EBMed specimens demonstrate better formability, tolerating higher compressive strains. The softening fraction substantially increases at high temperatures, indicating safe domains for thermomechanical processing of additively manufactured Ti6242 alloy.

show abstract

Section: Flow Stress Behaviormentioning

confidence: 83%

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy

Roshani,

Abedi,

Saboori

2023

Adv Eng Mater

View full text Add to dashboard Cite

show abstract

“…The tactical missiles and war shot torpedoes are powered by automatically remotely activated zinc-silver batteries with long life and instant activation capability. 17,18 Table I lists a number of automatically activated batteries which have been designed to meet various specific applications.…”

Section: Applicationsmentioning

confidence: 99%

Review—Status of Zinc-Silver Battery

Zhang

Song

et al. 2019

J. Electrochem. Soc.

View full text Add to dashboard Cite

As the capacity reach as high as 350 Wh•kg −1 and 750 Wh•L −1 , zinc-silver batteries are widely used in military, aerospace and other fields because of their high specific energy and discharging rate, together with their safety and reliability. In this paper, the researches progresses of silver oxide electrode in eliminating high plateau stage, improving thermal stability and its structure are reviewed. Also the corrosion inhibitor of zinc electrode to prevent hydrogen evolution is summarized. In addition, the technical progress of battery separator is presented. The developing trends of the zinc silver battery are prospected.

show abstract

Research on Safety Assessment for Power Line Design

Cited by 2 publications

References 2 publications

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy

Comparing the Cold, Warm, and Hot Deformation Flow Behavior of Selective Laser‐Melted and Electron‐Beam‐Melted Ti–6Al–2Sn–4Zr–2Mo Alloy

Review—Status of Zinc-Silver Battery

Contact Info

Product

Resources

About