Resource recovery of animal bones: Study on sorptive properties and mechanism for Sr2+ ions

Smičiklas, Ivana; Dimović, Slavko; Šljivić, M.; Plećaš, I.; Lončar, B.; Mitrić, Miodrag

doi:10.1016/j.jnucmat.2010.02.004

Cited by 24 publications

(17 citation statements)

References 26 publications

Supporting

Mentioning

Contrasting

Unclassified

Order By: Relevance

“…Therefore, in our design, the levels of these factors were selected in wide ranges. According to the results of previous studies [19,20], annealing at 400°C was found to produce the materials with the best sorption properties. The treatment at this particular temperature was chosen as discontinuous factor, in order to compare the effect of thermal and chemical treatments and to detect their potential synergic effects.…”

Section: Preparation Of Sorbents: Experimental Designmentioning

confidence: 82%

“…The selection of process variables and their levels was made based on the survey of the literature concerning the effects of different treatments on sorption properties and applicability of bone produced materials [19,20,[22][23][24]. As the main process variables, the following five were considered: type and the concentration of the chemical reagent, reaction temperature, reaction time, and annealing.…”

Section: Preparation Of Sorbents: Experimental Designmentioning

confidence: 99%

“…The increase of specific surface area was found to be remarkable, however, 50 % of the overall value is accounted for carbon phase, which is less efficient and less selective cation sorbent than HAP. A systematic study on the influence of heating temperature (in the range 400-1000°C) on bone sorption properties was also performed [19,20]. Annealing at 400°C caused incomplete combustion of bone organic components.…”

Section: Introductionmentioning

confidence: 99%

See 2 more Smart Citations

Evaluation of the effects of treatment factors on the properties of bio-apatite materials

et al. 2014

Self Cite

View full text Add to dashboard Cite

Animal bones have been studied as a resource of low-crystalline apatite for immobilization of toxic heavy metals. Chemical and thermal treatments can be applied for selective removal of bone organic constituents. In this study, the impact of different treatment factors was determined by experimental design methodology, and comparison of the estimated effects was performed in order to optimize the treatment conditions. Fractional factorial design with five variables at two levels was applied for factors screening. The type of chemical reagent (H 2 O 2 or NaOH), its concentration (0.1 or 2 mol/L), reaction temperature (20 or 60°C), contact time (1 or 3 h) and sample annealing (without or at 400°C) were considered as process variables. Structural properties of bone sorbents, loss of ignition, point of zero charge, surface functional groups, specific surface area, chemical composition, and Cd 2? sorption efficiency, were selected as system responses. Samples significantly differed in respect to the organic phase content and composition, thus mechanisms of Cd 2? sorption were complex. Statistical analysis has revealed that, between all studied factors, temperature treatment was the most important for sorbents increased specific surface area, porosity and cation sorption. Furthermore, NaOH was more effective than H 2 O 2 , while the effects produced by variation of other factors were less pronounced. The highest proportion of bio-apatite with desired low crystallinity and high specific surface area was achieved by synergetic effects of chemical treatment with NaOH and thermal treatment at 400°C.

show abstract

Section: Preparation Of Sorbents: Experimental Designmentioning

confidence: 82%

Section: Preparation Of Sorbents: Experimental Designmentioning

confidence: 99%

Section: Introductionmentioning

confidence: 99%

See 1 more Smart Citation

Evaluation of the effects of treatment factors on the properties of bio-apatite materials

et al. 2014

Self Cite

View full text Add to dashboard Cite

show abstract

“…The ex tremely high amounts of gen er ated con struc tion/de mo li tion waste are de pos ited on the land fills cov er ing large ar eas, there fore it is es sen tial to de velop tech nol o gies for fine frac tion uti li za tion and minimization of dis posed quan ti ties. Gen er ally, the vari ety of waste ma te ri als showed rel a tive high af fin i ties to wards ra dio ac tive ions, in di cat ing the prom is ing uti liza tion tool for LRW treat ment and also the pos si bil ity of re cy cling and minimization [2][3][4].…”

Section: Introductionmentioning

confidence: 99%

The application of experimental design methodology for the investigation of liquid radioactive waste treatment

et al. 2017

View full text Add to dashboard Cite

1 Vin~a In sti tute of Nu clear Sci ences, Uni ver sity of Bel grade, Bel grade, Ser bia 2 Fac ulty of Ap plied Ecol ogy, Singidunum Uni ver sity, Bel grade, Ser bia 3 Fac ulty of Ge og ra phy, Uni ver sity of Bel grade, Bel grade, Ser bia 4 Fac ulty of Tech nol ogy and Met al lurgy, Uni ver sity of Bel grade, Bel grade, Ser bia Sci en tific pa per http://doi.org/10.2298/NTRP1703281SThe sorp tion prop er ties of waste fa cade, brick, and as phalt sam ple to wards Sr(II), Co(II), and Ni(II) ions from sin gle and multicomponent so lu tions were in ves ti gated. The high est sorp tion ca pac ity was found for Ni(II) ions, while the most ef fec tive sorbent was fa cade. Simplex Cen troid Mix ture De sign was used in or der to in ves ti gate the sorp tion pro cesses of ions from so lu tions with dif fer ent com po si tion as well as the com pe ti tion be tween the cat ions. Based on the sta tis ti cal anal y sis re sults, the equa tions for data mod el ing were pro posed. Accord ing to the ob ser va tions, the in ves ti gated solid ma tri ces can be ef fec tively used for the liquid ra dio ac tive waste treat ment. Fur ther more, the ap plied meth od ol ogy turned out to be an easy and op er a tional way for the in ves ti ga tions of multicomponent sorp tion pro cesses.

show abstract

“…Heating in air atmosphere is one of the methods for decomposition of organic compounds. The influence of heating temperature on bone physicochemical and sorption properties has been investigated, and the optimal temperature was found to be 400 °C [15,18]. At lower temperatures organic phase was removed incompletely, while higher temperatures resulted in sintering of HAP nanoparticles and deterioration of sorption capacities.…”

mentioning

confidence: 99%

Ni(II) immobilization by bio-apatite materials: Appraisal of chemical, thermal and combined treatments

Šljivić-Ivanović¹,

Milenković²,

Jović³

et al. 2016

CI&CEQ

View full text Add to dashboard Cite

Article Highlights • Apatite materials derived from bovine bones were studied as Ni(II) ions sorbents • Raw bones were compared with chemically, thermally and chemically/thermally treated samples • Different sorption mechanisms were identified by sorption data and FT-IR spectra analysis • Combined chemical/thermal treatment produced material with the highest sorption capacity • Sorbed Ni(II) was very stable at low sorbent loads, while largely mobile at high loadings

show abstract

Resource recovery of animal bones: Study on sorptive properties and mechanism for Sr2+ ions

Cited by 24 publications

References 26 publications

Evaluation of the effects of treatment factors on the properties of bio-apatite materials

Evaluation of the effects of treatment factors on the properties of bio-apatite materials

The application of experimental design methodology for the investigation of liquid radioactive waste treatment

Ni(II) immobilization by bio-apatite materials: Appraisal of chemical, thermal and combined treatments

Contact Info

Product

Resources

About