Sanding in Oil Well Reservoir Completions

Nwabueze, Vincent; Onikoyi, Abiola S.; Okoro, Felix; Ajienka, J.A.

doi:10.2118/163010-ms

Cited by 9 publications

(1 citation statement)

References 2 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Sand production occurs when the stress on the formation exceeds the formation strength and results in rock failure due to tectonic activities, overburden pressure, increase in the production rate of reservoir fluid due to a large pressure drawdown between the reservoir pressure and wellbore flowing pressure, stress induced during drilling, and also producing fluid drag force [2].…”

Section: Introductionmentioning

confidence: 99%

Effect of Produced Sand Particles and Fines on Scale Inhibitor: A Review

Anyanwu

Oluyemi

2021

Colloids and Interfaces

View full text Add to dashboard Cite

Application of scale inhibitors in oil and gas production is aimed at mitigating scale blockage during production. Many experimental, mathematical, and numerical simulation modeling works have been carried out to evaluate behavior, performance, and interaction of the scale inhibitor chemicals within porous media in relation to their efficiency in solving scale problem. However, the mechanisms underpinning scale inhibitors performance are not well published. Some research works have shown theoretically that not all scale inhibitors pumped into the formation adsorb onto the formation rock. Some of the inhibitors may adsorb on produced loose sand grains or colloidal fine sand particles which float and flow within the pore spaces along with the scale inhibitor mostly in unconsolidated reservoirs This paper provides a review of research work on the effect of produced loose sand or colloidal fine particles flow on polyphosphonates and polyphosphinopolymer scale inhibitors performances during crude production.

show abstract

Section: Introductionmentioning

confidence: 99%

Effect of Produced Sand Particles and Fines on Scale Inhibitor: A Review

Anyanwu

Oluyemi

2021

Colloids and Interfaces

View full text Add to dashboard Cite

show abstract

Determination of regions prone to sand production and the linkage to fluid flow rates by integrating rock strength parameters and microphotographs in the southern onshore basin, India

Kukshal,

Sharma,

Kalita

et al. 2023

J Petrol Explor Prod Technol

View full text Add to dashboard Cite

One of the main challenges for healthy hydrocarbon yields from the production wells is the sand production, and its control assumes significant importance for successful production operations. The prime objective remains to control the sand production without compromising on the fluid flow rates. Sand production is conventionally associated with diverse heterogeneous formations, especially poorly consolidated formations. Scrutinizing fluid flow rates at different orientations of perforations is a valuable analysis in controlling the sand production. This study was conducted to examine the case of sand production in a few development wells from Malleshwaram field of the Krishna Godavari (KG) basin in south India and provide alternatives to arrest this sand production. The influence of oriented perforations on fluid flow rates to minimize sanding tendencies was examined. Sand grain diameter was estimated using the distribution plots of the grain sizes obtained from the photomicrographs, and the average value of the grain size was estimated around 100 μm. The fluid flow model was simulated for actual scenario in the hydrocarbon bearing Nandigama formation using finite element modeling (FEM). Sanding tendencies in these formations were studied at varying depletion rates. Critical draw down pressure (CDDP), which is a function of both critical bottom hole pressure and reservoir pore pressure, for well 1 and well 2 is estimated as 4650 Psi and 3400 Psi, respectively, at 0% depletion. CDDP was used to estimate the onset of sanding, and the flow rate for horizontal perforation was calculated as 0.024548 $${\mathrm{m}}^{3}$$ m 3 /sec. Strength parameters, namely the unconfined compressive strength (UCS) and cohesion, were also investigated in all the wells to decipher the formation strength and a possible linkage to sanding. These results present a completely fresh analysis of the sanding potential and the related parameters responsible for it in these formations. Fluid flow rates for the producing reservoir are studied at different set of oriented and sized perforations. It was observed that a hiked flow rate in horizontal perforations maintains the production in a safe and no-sanding zone. This study provides vital information and a workflow for similar heterogeneous complex formations for designing the well completions, augmenting economic production and reinforcing future reservoir management.

show abstract

An Accurate Critical Total Drawdown Prediction Model for Sand Production: Adaptive Neuro-fuzzy Inference System (ANFIS) Technique

Alakbari,

Mahmood,

Mohyaldinn

et al. 2024

Arab J Sci Eng

View full text Add to dashboard Cite

Sand production causes many problems in the petroleum industry. The sand production is predicted to control it in the early stages. Therefore, accurate prediction of sand production has been considered substantial in achieving successful sand control. Critical total drawdown (CTD) can indicate the sand production. The main drawback of the previous studies in predicting CTD is their lack of accuracy. Thus, this study aims to develop an accurate CTD estimation prediction model employing a trend analysis and adaptive neuro-fuzzy inference system (ANFIS). The method is chosen because of its higher performance; the model is built based on 23 published datasets from the Adriatic Sea. The developed ANFIS model is evaluated using various methods, namely, trend analyses. Trend analyses are conducted to show the effects of the features on the CTD to present the physical behavior. The model’s performance was also evaluated using statistical error analyses. In addition, the ANFIS and previously published models were assessed. The trend analyses show the correct relationship between all features and the CTD. In addition, the trend analyses for the previous models are discussed. The results show that the proposed ANFIS method outperforms published methods with an R of 0.9984 and an absolute average percentage relative error (AAPRE) of 4.293%.

show abstract

Sanding in Oil Well Reservoir Completions

Cited by 9 publications

References 2 publications

Effect of Produced Sand Particles and Fines on Scale Inhibitor: A Review

Effect of Produced Sand Particles and Fines on Scale Inhibitor: A Review

Determination of regions prone to sand production and the linkage to fluid flow rates by integrating rock strength parameters and microphotographs in the southern onshore basin, India

An Accurate Critical Total Drawdown Prediction Model for Sand Production: Adaptive Neuro-fuzzy Inference System (ANFIS) Technique

Contact Info

Product

Resources

About