Statistical analysis on mechanical properties of friction-stir-welded AA 1050/AA 5083 couples

Sarsılmaz, Furkan; Çaydaş, Ulaş

doi:10.1007/s00170-008-1716-x

Cited by 40 publications

(24 citation statements)

References 20 publications

Supporting

Mentioning

Contrasting

Order By: Relevance

“…Among the AA 5XXX series of aluminium alloys, the FSW of AA 5083 is the most studied, either in similar [12][13][14][15][16][17][18][19][20][21][22] and dissimilar 23,24 welding combinations.…”

Section: Introductionmentioning

confidence: 99%

Microstructural and mechanical characterisation of 5XXX-H111 friction stir welded tailored blanks

Tronci

McKenzie

Leal

et al. 2011

Science and Technology of Welding and Joining

View full text Add to dashboard Cite

Friction stir welds in 1 mm thick plates of AA 5182-H111 and AA 5083-H111 aluminium alloys are analysed in this paper. The welds were produced using a large range of welding conditions, namely, different process control modes (position and load control), tool parameters (different geometries and dimensions) and process parameters (rotation speed, advancing speed and axial load). Visual inspection and metallographic and mechanical analysis demonstrate that it is possible to obtain consistently good quality welds in very thin plates under a large range of welding conditions. Important relations between base material properties, tool geometry and the final properties of the welds were established

show abstract

Section: Introductionmentioning

confidence: 99%

Microstructural and mechanical characterisation of 5XXX-H111 friction stir welded tailored blanks

Tronci

McKenzie

Leal

et al. 2011

Science and Technology of Welding and Joining

View full text Add to dashboard Cite

show abstract

“…To evaluate the optimum conditions of FSW process parameters with respect to FSW butt weld quality; in this study, there are three primary controllable factors and their three levels [8] and [9] are shown in Table 3. The plan of the experiments as shown in Table 4.…”

Section: Selection Of Fsw Parameters and Levelsmentioning

confidence: 99%

“…By neglecting the values of the initial and the end pieces from each set of 2 piece trial under same experimental condition, averaged ultimate tensile strength and hardness are calculated and are shown in Table 5. The resulting averaged elongation rate is shown in Table 6.The objective of using Taguchi technique was to reduce the time and cost to evaluate the optimum welding conditions [9]. …”

Section: Selection Of Fsw Parameters and Levelsmentioning

confidence: 99%

Optimizing the Process Parameters of Friction Stir Butt Welded Joint on Aluminum Alloy Aa6061-T6

.¹

2014

IJRET

View full text Add to dashboard Cite

show abstract

“…Mirjalili et al (2013) also improved the grain structure of AA 2017 (artificially aged) by FSW. Sarsılmaz et al (2009) investigated the influence of input parameters viz. transverse speed, stirrer geometry and spindle rotational speed on UTS and the nugget hardness of friction stir welded AA 1050/AA 5083 alloys by ANOVA.…”

Section: Introductionmentioning

confidence: 99%

Dissimilar alloys (AA6082/AA5083) joining by FSW and parametric optimization using Taguchi, grey relational and weight method

Jain¹,

Sharma²,

Gupta³

2018

10.5267/j.esm

View full text Add to dashboard Cite

This work is focused on the influence of different friction stir welding (FSW) parameters on AA6082 T-6 and AA5083-O alloys welding quality, by using Taguchi, Grey Relational and Weight Method. Four welding parameters were investigated, namely tool rotation speed (TRS), welding speed (WS), tool pin profile (TPP) and shoulder diameter (SD). The optimized setting of these input parameters was investigated so that weld parts quality could be optimized. Analysis of variance (ANOVA) was used to investigate the effects of these welding process parameters on response variables, viz. elongation (EL) and ultimate tensile strength (UTS). Single response optimization was carried using Taguchi Technique while grey relational analysis (GRA) was used for simultaneous optimization of two responses. Once the optimal settings of control factors were identified, confirmation experiments were performed for the validation of results. In the multi-response optimization, TRS was found to have the maximum effect (57.9%), followed by WS, SD and TPP. Weight method was applied for providing the priority to the response (i.e. EL and UTS). The response with higher priority presented a weight equal to 0.7, while the lower priority given corresponds to a weight of 0.3.

show abstract

Statistical analysis on mechanical properties of friction-stir-welded AA 1050/AA 5083 couples

Cited by 40 publications

References 20 publications

Microstructural and mechanical characterisation of 5XXX-H111 friction stir welded tailored blanks

Microstructural and mechanical characterisation of 5XXX-H111 friction stir welded tailored blanks

Optimizing the Process Parameters of Friction Stir Butt Welded Joint on Aluminum Alloy Aa6061-T6

Dissimilar alloys (AA6082/AA5083) joining by FSW and parametric optimization using Taguchi, grey relational and weight method

Contact Info

Product

Resources

About